Convective boundary layer

Let us try to preserve convection. If we ignore Il6 but maintain the more correct turbulent boundary layer convection (Equation (12.24)), then... 

The relationship between heat transfer and the boundary layer species distribution should be emphasized. As vaporization occurs, chemical species are transported to the boundary layer and act to cool by transpiration. These gaseous products may undergo additional thermochemical reactions with the boundary-layer gas, further impacting heat transfer. Thus species concentrations are needed for accurate calculation of transport properties, as well as for calculations of convective heating and radiative transport. 

At any point within the boundary layer, the convective flux of the macromolecule solute to the membrane surface is given by the volume flux,/ of the solution multipfled by the concentration of retained solute, c. At steady state, this convective flux within the laminar boundary layer is balanced by the diffusive flux of retained solute in the opposite direction. This balance can be expressed by equation 1 ... 

A simplified model usiag a stagnant boundary layer assumption and the one-dimension diffusion—convection equation has been used to calculate wall concentration ia an RO module. The iategrated form of this equation, the widely appHed film theory (41), is given ia equation 8. 

In considering the effect of mass transfer on the boiling of a multicomponent mixture, both the boiling mechanism and the driving force for transport must be examined (17—20). Moreover, the process is strongly influenced by the effects of convective flow on the boundary layer. In Reference 20 both effects have been taken into consideration to obtain a general correlation based on mechanistic reasoning that fits all available data within 15%. 

The concentration boundary layer forms because of the convective transport of solutes toward the membrane due to the viscous drag exerted by the flux. A diffusive back-transport is produced by the concentration gradient between the membranes surface and the bulk. At equiUbrium the two transport mechanisms are equal to each other. Solving the equations leads to an expression of the flux ... 

I. Turbulent, local flat plate, natural convection, vertical plate Turbulent, average, flat plate, natural convection, vertical plate Nsk. = — = 0.0299Wg=Ws = D x(l + 0.494W ) )- = 0.0249Wg=W2f X (1 + 0.494WE )- [S] Low solute concentration and low transfer rates. Use arithmetic concentration difference. Ncr > 10 " Assumes laminar boundary layer is small fraction of total. D [151] p. 225... 

The determining factor in convection is the flow boundary layer. Outside the boundary layer, the fluid is considered to have achieved a maximum velocity at an infinite distance from the surface. 

If steam condenses on a surface, there is no boundary layer the resistance to heat flow is due to scale, metal thickness, and the condensed liquid layer, resulting in a high heat transfer factor. A thin layer of air or other noncondensing gas forms at the surface through which the steam diffuses. The heat transfer factor diminishes rapidly but is considerably higher than in dry convection. 

In some convection equations, such as for turbulent pipe flow, a special correction factor is used. This factor relates to the heat transfer conditions at the flow inlet, where the flow has not reached its final velocity distribution and the boundary layer is not fully developed. In this region the heat transfer rate is better than at the region of fully developed flow. 

Figures 4.34 and 4.35 represent two extreme cases. Drying processes represent the case shown in Fig. 4.34 and distillation processes represent Fig. 4.35. Neither case represents a convective mass transfer case while the gas flow is in the boundary layer, other flows are Stefan flow and turbulence. Thus Eqs. (4.243) and (4.244) can seldom be used in practice, but their forms are used in determining the mass transfer factor for different cases.

In the previous section we discussed wall functions, which are used to reduce the number of cells. However, we must be aware that this is an approximation that, if the flow near the boundary is important, can be rather crude. In many internal flows—where all boundaries are either walls, symmetry planes, inlets, or outlets—the boundary layer may not be that important, as the flow field is often pressure determined. However, when we are predicting heat transfer, it is generally not a good idea to use wall functions, because the convective heat transfer at the walls may be inaccurately predicted. The reason is that convective heat transfer is extremely sensitive to the near-wall flow and temperature field. 

Above this size, the flow of air over the condenser surface will be by forced convection, i.e. fans. The high thermal resistance of the boundary layer on the air side of the heat exchanger leads to the use, in all but the very smallest condensers, of an extended surface. This takes the form of plate fins mechanically bonded onto the refrigerant tubes in most commercial patterns. The ratio of outside to inside surface will be between 5 1 and 10 1. 

J6. Jiji, L. M Incipient boiling and the bubble boundary layer formation over a heated plate for forced convection flow in a pressurized rectangular channel, Ph.D. Thesis, Univ. of Michigan, Ann Arbor, 1962. 

Another widely used concept is that of a planetary boundary layer (PBL) in contact with the surface of the Earth above which lies the "free atmosphere." This PBL is to some degree a physically mixed layer due to the effects of shear-induced turbulence and convective overturning near the Earth s surface. 

At present there is no small-scale test for predicting whether or how fast a fire will spread on a wall made of flammable or semiflammable (fire-retardant) material. The principal elements of the problem include pyrolysis of solids char-layer buildup buoyant, convective, tmbulent-boundary-layer heat transfer soot formation in the flame radiative emission from the sooty flame and the transient natme of the process (char buildup, fuel burnout, preheating of areas not yet ignited). Efforts are needed to develop computer models for these effects and to develop appropriate small-scale tests. 

Fluid flow and reaction engineering problems represent a rich spectrum of examples of multiple and disparate scales. In chemical kinetics such problems involve high values of Thiele modulus (diffusion-reaction problems), Damkohler and Peclet numbers (diffusion-convection-reaction problems). For fluid flow problems a large value of the Mach number, which represents the ratio of flow velocity to the speed of sound, indicates the possibility of shock waves a large value of the Reynolds number causes boundary layers to be formed near solid walls and a large value of the Prandtl number gives rise to thermal boundary layers. Evidently, the inherently disparate scales for fluid flow, heat transfer and chemical reaction are responsible for the presence of thin regions or "fronts in the solution. 

A similar situation occurs in the case of free convection and exothermic chemical reaction phenomena where the hydrodynamic boundary layer is separated from the reaction front. 

Surface Polarization in TFF The simplified model of polarization shown in Fig. 20-47 is used as a basis for analyzing more complex systems. Consider a single component with no reaction in a thin, two-dimensional boundary layer near the membrane surface. Axial diffusion is negligible along the membrane surface compared to convection. 

Further neglecting the first term allows integration from y = 0 at the wall (membrane surface) into the boundary layer. At the wall, the net flux is represented by convection into the permeate... 

---