Benzenes vinyl acetate

Methyl methacrylate Benzene d 6-Benzene Vinyl acetate Benzene dg-Benzene... 

With each succeeding year in the 1950s and 1960s there was a swing away from coal and vegetable sources of raw materials towards petroleum. Today such products as terephthalic acid, styrene, benzene, formaldehyde, vinyl acetate and acrylonitrile are produced from petroleum sources. Large industrial concerns that had been built on acetylene chemistry became based on petrochemicals whilst coal tar is no longer an indispensable source of aromatics. 

Katz et al. also plotted the distribution coefficient of n-pentanol, benzonitrile and vinyl acetate against the concentration of unassociated methanol in the solvent mixture and the results are shown in Figure 32. It is seen that the distribution coefficient of all three solutes is predominantly controlled by the amount of unassociated methanol in the aqueous solvent mixture. In addition, the distribution coefficient increases linearly with the concentration of unassociated methanol for all three solutes over the entire concentration range. The same type of curves for anisole and benzene, shown in Figure 33, however, differ considerably. Although the relationship between distribution coefficient and unassociated methanol concentration is approximately linear up to about 50%v/v of unassociated methanol, over the entire range the... 

Free-radical copolymerization of vinyl acetate with various vinyl siloxane monomers was described 345). Reactions were conducted in benzene at 60 °C using AIBN as the initiator. Reactivity ratios were determined. Selective hydrolysis of the vinyl acetate units in the copolymer backbone was achieved using an aqueous sodium hy-droxide/THF mixture. The siloxane content and degree of hydrolysis were determined by H-NMR. 

Fig. 39.—Plots of c/c against c from the data of Masson and Melville for the following solvent-polymer pairs curve 1, polyacrylonitrile in dimethylformamide at 13.5° C curves 2 and 4, poly-(vinyl acetate) s in benzene at 20°C curve 3, polyacenaphthylene in benzene at 25°C curve 5, polyvinylxylene in benzene at 24°C curve 6, poly-(methyl methacrylate) in benzene at 16°C. All curves have been calculated from Eq. (13). Units correspond to those in Fig. 38. (Fox, Flory, and Bueche. )...

Figure 12.5 Pyrogram of Mowilith 30, a vinyl acetate polymer used in conservation. Peak assignments 1, acetic acid 2, benzene 3, styrene 4, indene 5, 1,2 dihydro naphthalene 6, naphthalene 7, 2 methyl naphthalene 8, 1 methyl naphthalene 9, biphenyl 10, fluorene 11, anthracene...

Figure 12.11 Pyrograms of a PVAc paint containing external plasticizers (a), and of a vinyl acetate/VeoVa copolymer (b). Peak assignments 1, acetic acid, 2, benzene, 3, butyl acetate, 4, butyl benzoate, 5, bis(2 methylpropyl) phthalate, 6, dibutylphthalate, 7, branched acrylates ranging from C7 to C9...

Rhodium complexes catalyze the oxidative coupling of benzene with ethene to produce styrene directly.45,45a,45b Using Rh(ppy)2(OAc) (ppyH = 2-phenylpyridine), the reaction of benzene with ethene in the presence of 02 and Cu(OAc)2 in benzene and acetic acid at 180 °C gives styrene and vinyl acetate in 77% and 23% selectivities, respectively. 

The hydration state of risedronate sodium was monitored continuously in a fluidized bed dryer and correlated to data on the physical stability of tablets made from the monitored material [275]. The final granulation moisture was found to affect the solid-state form, which in turn dictated the drug s physical stability over time. The process of freeze-drying mannitol was monitored continuously with in-line Raman and at-line NIR spectroscopies [276]. The thin polymer solvent coatings, such as poly(vinyl acetate) with toluene, methanol, benzene, and combinations of the solvents, were monitored as they dried to generate concentra-tion/time profiles [277]. 

Many substituents stabilize the monomer but have no appreciable effect on polymer stability, since resonance is only possible with the former. The net effect is to decrease the exothermicity of the polymerization. Thus hyperconjugation of alkyl groups with the C=C lowers AH for propylene and 1-butene polymerizations. Conjugation of the C=C with substituents such as the benzene ring (styrene and a-methylstyrene), and alkene double bond (butadiene and isoprene), the carbonyl linkage (acrylic acid, methyl acrylate, methyl methacrylate), and the nitrile group (acrylonitrile) similarly leads to stabilization of the monomer and decreases enthalpies of polymerization. When the substituent is poorly conjugating as in vinyl acetate, the AH is close to the value for ethylene. 

Radical chain polymerizations are characterized by the presence of an autoacceleration in the polymerization rate as the reaction proceeds [North, 1974], One would normally expect a reaction rate to fall with time (i.e., the extent of conversion), since the monomer and initiator concentrations decrease with time. However, the exact opposite behavior is observed in many polymerizations—the reaction rate increases with conversion. A typical example is shown in Fig. 3-15 for the polymerization of methyl methacrylate in benzene solution [Schulz and Haborth, 1948]. The plot for the 10% methyl methacrylate solution shows the behavior that would generally be expected. The plot for neat (pure) monomer shows a dramatic autoacceleration in the polymerization rate. Such behavior is referred to as the gel effect. (The term gel as used here is different from its usage in Sec. 2-10 it does not refer to the formation of a crosslinked polymer.) The terms Trommsdorff effect and Norrish-Smith effect are also used in recognition of the early workers in the field. Similar behavior has been observed for a variety of monomers, including styrene, vinyl acetate, and methyl methacrylate [Balke and Hamielec, 1973 Cardenas and O Driscoll, 1976, 1977 Small, 1975 Turner, 1977 Yamamoto and Sugimoto, 1979]. It turns out that the gel effect is the normal ... 

Finally, we should mention the phenomenon of incompatibility of mixtures of polymer solutions. It applies to nearly all combinations of polymer solutions when the homogeneous solutions of two different polymers in the same solvent are mixed, phase separation occurs. For example, 10% solutions of polystyrene and poly(vinyl acetate), each in benzene, form two separated phases upon mixing. One phase contains mainly the first polymer, the other phase mainly the second polymer, but in both phases there is a certain amount of the other polymer present. This limited compatibility of polymer mixtures can be explained thermodynamically and depends on various factors, such as the structure of the macromolecule, the molecular weight, the mixing ratio, the overall polymer concentration, and the temperature. 

By-products formed during their preparation (e.g., ethylbenzene and divinyl-benzenes in styrene acetaldehyde in vinyl acetate) added stabilizers (inhibitors) autoxidation and decomposition products of the monomers (e.g., perox-... 

PSVBDEP poly(styrene-co-4-vinyl benzene phosphonic acid diethyl ester) PVAc poly(vinyl acetate)... 

---