Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

ASTM ASTME

Urethane Raw ASTM ASTM ASTM ASTM ASTM ASTM ASTM ASTM ASTM ASTM ASTM MIL-F... [Pg.369]

Product ASTM ASTM ASTM ASTM ASTM ASTM... [Pg.309]

Product ASTM ASTM ASTM ASTM------------------ ASTM ASTM... [Pg.305]

ASTM ASTM ASTM ASTM ASTM CPSC PFF 6 DOC FF 4... [Pg.424]

Test standard ASTM ASTM ASTM ASTM D-256 ASTM D-1238 ... [Pg.342]

Product no. Durometer Tensile Elonga-Spedfic hardness strength, tion, gravity shore psi percent ASTM ASTM ASTM ASTM D-792 D-2240 D-412 D-412 Modulus Tear ASTM strength D-412 pli,die B... [Pg.322]

Product no. Specific Durometer hardness, gravity shore ASTM ASTM D-792 D-2240 Tensile Tear strength. Elongation, strength psi percent pli, die B ASTM ASTM ASTM D-412 D-412 D-624 ... [Pg.320]

Conduct in-house inhibitor tests to determine which inhibitor and at what concentration to use. The tests must be conducted following the recommended practices of NACE or ASTM. ASTM (American Society for Testing and Materials) and NACE (National Association of Corrosion Engineers) publish standards for such tests. [Pg.1330]

ASTM Test Methods from ASTM. ASTM, 1916 Race Street, Philadelphia, PA 19103. [Pg.27]

ASTM, ASTM International Web site, American Society for Testing and Materials, West Conshohocken, PA, www.astm.org, 2009. [Pg.1152]

ASTM. ASTM Standards on Environmental Site Characterization, ASTM, 2002 1827 p. DeChacon, J.R. Van Houten, N.J. Indoor air quality. Natl. Environ. J. 1991, 16-18 Nov. [Pg.130]

An important consideration in sample preservation is the observance of holding time, which is defined by ASTM (ASTM, 1987) as follows The period of time during which a water sample can be stored after collection and preservation without significantly affecting the accuracy of analysis. ... [Pg.100]

American Standard Testing Methods (ASTM), ASTM-IP Petroleum Measurement Tables and Standard Testing Methods, ASTM, Washington DC, 1952. [Pg.36]

Micro activity test (MAT). This test was developed and standardized by ASTM (ASTM-D-3907). In the MAT test, a sample of cracking catalyst is contacted with gas oil in a fixed-bed reactor. Gas chromatographic analysis on gas and liquid products is used to determine the yield structure. Recently, the MAT conditions have been adapted to simulate commercial units more accurately in terms of contact times. A higher catalyst activity results in improved conversion and higher regenerator temperature. [Pg.716]

American Society for Testing and Materials (ASTM), ASTM Method D-2879-70. ASTM Standards, Part 24, 1974,... [Pg.64]

The tests for change in dimensions of a polymer under long-term stress, called creep or cold flow (ASTM-D74-56), are no longer recommended by ASTM. ASTM-D-671 describes suggested tests for fatigue or endurance of plastics under repeated flexure. [Pg.37]

See other pages where ASTM ASTME is mentioned: [Pg.307]    [Pg.309]    [Pg.313]    [Pg.320]    [Pg.322]    [Pg.324]    [Pg.306]    [Pg.308]    [Pg.324]    [Pg.305]    [Pg.305]    [Pg.308]    [Pg.310]    [Pg.311]    [Pg.312]    [Pg.313]    [Pg.305]    [Pg.310]    [Pg.312]    [Pg.321]    [Pg.229]    [Pg.229]    [Pg.240]    [Pg.61]    [Pg.1023]    [Pg.174]    [Pg.125]    [Pg.136]    [Pg.333]    [Pg.511]   
See also in sourсe #XX -- [ Pg.471 , Pg.472 ]



SEARCH



ASTM

© 2024 chempedia.info