Appropriate temperatures

The values for unit weight of solvent (molality scale) can be obtained by multiplying the corresponding values for unit volume by the square root of the density of water at the appropriate temperature. 

HF is used as a source of fluorine for production of all the various fluorocarbon products. HF reacts in the presence of a suitable catalyst and under the appropriate temperature and pressure conditions with various organic chemicals to yield a family of products. A by-product stream of hydrochloric acid may be co-produced. 

The acryHc weak base resias are syathesized from copolymers similar to those used for the manufacture of weak acid cation-exchange resias. For example, uader appropriate temperature and pressure conditions, a weak acid resia reacts with a polyfuactioaal amine, such as dimethylaminopropylamine [109-55-7] (7) to give a weak base resia with a tertiary amine fuactioaaHty. 

Chemical Vapor Deposition. In chemical vapor deposition (CVD), often referred to as vapor transport, the desired constituent(s) to be deposited are ia the form of a compound existing as a vapor at an appropriate temperature. This vapor decomposes with or without a reducing or oxidizing agent at the substrate— vapor interface for film growth. CVD has been used successfully for preparing garnet and ortho ferrite films (24,25). Laser-assisted CVD is also practiced. 

The concentration of dissolved ionic substances can be roughly estimated by multiplying the specific conductance by an empirical factor of 0.55—0.9, depending on temperature and soluble components. Since specific conductance is temperature dependent, all samples should be measured at the same temperature. Alternatively, an appropriate temperature-correction factor obtained by comparisons with known concentrations of potassium chloride may be used. Instmments are available that automatically correct conductance measurements for different temperatures. 

The mercury barometer (Fig. 10-11) indicates directly the absolute pressure of the atmosphere in terms of height of the mercuiy column. Normal (standard) barometric pressure is 101.325 kPa by definition. Equivalents of this pressure in other units are 760 mm mercury (at 0°C), 29.921 iuHg (at 0°C), 14.696 IbFin, and 1 atm. For cases in which barometer readings, when expressed by the height of a mercuiy column, must be corrected to standard temperature (usually 0°C), appropriate temperature correction factors are given in ASME PTC, op. cit., pp. 23-26 and Weast, Handbook of Chemistty and Physics, 59th ed., Chemical Rubber, Cleveland, 1978-1979, pp. E39-E41. 

P = Pressure drop in inches of water SG = Specific gravity of the liquid on the tray at the appropriate temperature T = Number of trays T, = Tray spacing, in. 

The largest single use area for UPVC is for pipes and fittings. One particular area here is in chemical plant. It is of course necessary to check that all of the components of the PVC compound will be resistant to any of the chemicals with which the plant is liable to come into contact (at the appropriate temperatures) and also that additives will not be leached out by these chemicals. Particular uses are in acid recovery plant and in plant for handling hydrocarbons. 

One of the original applications of AES, and still one of the most important, is the analysis of grain boundaries in metals and ceramics. Very small amounts of impurity or dopant elements in the bulk material can migrate under appropriate temperature conditions to the boundaries of the grain structure and accumulate there. In that way the concentration of minor elements at the grain boundaries can become... 

In this example it has been assumed that the service temperature is 20 °C. If this is not the case, then curves for the appropriate temperature should be used. If these are not available then a linear extrapolation between temperatures which are available is usually sufficiently accurate for most purposes. If the beam in the above example had been built-in at both ends at 20 °C, and subjected to service conditions at some other temperature, then allowance would need to be made for the thermal strains set up in the beam. These could be obtained from a knowledge of the coefficient of thermal expansion of the beam material. This type of situation is illustrated later. 

The two major conditions that promote hydrate formation are (1) the gas being at the appropriate temperature and pressure, and (2) the gas being at or below its water dew point with free water present. For any particular composition of gas at a given pressure there is a temperature below which hydrates will form and above which hydrates will not form. As the pressure increases, the hydrate formation temperature also increases. If there is no... 

Among these three polybibenzoates, PTEB has a smectic mesophase stable during several days at any temperature below its isotropization point, although the transformation into a three-dimensional crystal can be attained by annealing at the appropriate temperatures, thus making it possible to analyze the effect of the thermal history on the dynamic mechanical relaxations of PTEB [27]. 

Table 7-10 pre.sents a temperature conversion table for various metals from one manufacturer for conventional pre-bulged, ten-sion-loaded disks with pressure on concave side (not prescored) as an illustration of the effect of lower or elevated temperatures referenced to 72°F on the burst pressure of a stamped disk. For other types of disk designs and from other manufacturers, the specific data for the style disk must be used to make the appropriate temperature correction. 

For diffusion controlled corrosion reactions e.g. dissolved oxygen reduction, and the effect of temperature which increases diffusion rates, then by substituting viscosity and the diffusion coefficients at appropriate temperatures into the Reynolds No. and Schmidt No., changes in corrosion rate can be calculated. 

The next step is to decide a suitable evaporating temperature. This will be set by the required load condition and the appropriate temperature differential (AT) across the evaporator. In the context of evaporator selection, the AT used is the difference between the evaporating refrigerant and the temperature of the fluid entering the cooler, not the log mean temperature difference (see [1-5]). 

The process, as described by Equation (131), is performed at a temperature of about 200-350°C [113]. Vapors of the water formed, ammonia and hydrogen fluoride, are separated from the interaction zone and collected for reuse by condensation at appropriate temperatures in the form of ammonium fluoride, NH F, or ammonium hydrofluoride, NH4HF2. 

The fluorine concentration in hydrofluorides of tantalum and niobium is an extremely important issue. Fluorine that separates into the gaseous phase interacts with the construction elements of the furnaces, leading to additional contamination of the final product by silicon, aluminum, etc. Thus, it is recommended to perform diying in crucibles made of Teflon or polypropylene with appropriate temperature limitations. Use of crucibles made of carbon-glass ensures high quality and a broad working temperature range, at least up to 300-350°C. 

The catalytic activity of the pure /3-palladium hydride has been studied under the appropriate temperature and pressure conditions. The palladium sample was converted into the hydride in a manner which bypassed the area of coexistence of the phases. This was achieved by suitably saturating the metal with hydrogen at 35 atm above the critical temperature and then subsequently cooling the sample to the required temperature and reducing the hydrogen pressure. This method of sample prepare tion allowed one to avoid cracking the palladium crystallites, which would... 

Following this, elastomers can be swollen by some high-pressure gases (especially CO2) as the densities of these gases approach liquid-like levels, at appropriate temperatures they become supercritical fluids which possess a solubility parameter magnitudes that, however, are highly dependent on temperature and pressure... 

What happens to a substance as pressure changes at constant temperature can be determined by drawing a vertical line at the appropriate temperature on the phase diagram. 

---