Anionic polymerization alkali metals

An interesting feature of the ring opening polymerization of siloxanes is their ability to proceed via either anionic or cationic mechanisms depending on the type of the catalyst employed. In the anionic polymerization alkali metal hydroxides, quaternary ammonium (I NOH) and phosphonium (R POH) bases and siloxanolates (Si—Oe M ) are the most widely used catalysts 1,2-4). They are usually employed at a level of 10 2 to KT4 weight percent depending on their activities and the reaction conditions. The activity of alkali metal hydroxides and siloxanolates decrease in the following order 76 79,126). 

Arsenites of the alkali metals are very soluble in water, those of the alkaline earth metals less so, and those of the heavy metals are virtually insoluble. Many of the salts are obtained as meta-arsenites, e.g. NaAs02, which comprises polymeric chain anions formed by comer linkage of pyramidal ASO3 groups and held together by Na ions ... 

In anionic polymerization, as in carbonium ion polymerization, termination does not involve bimolecular reaction between two growing chains. Neither can recombination of ions lead to termination, since a carbon-metal bond is highly polar, in the case of alkali metals frequently completely ionized, and in every case very reactive. The termination step leading to the formation of a terminal C=C double bond is not too probable. This reaction involves the formation of a metal hydride, and this does not contribute greatly to the driving force. Consequently, such a termination is observed at higher temperatures only and it is probably more common in coordination polymerization where the metals involved are less electropositive. 

Some of the results of bulk polymerization of 61 by using different anionic catalysts are summarized in Table 858 It was easily polymerized in the presence of alkali metal compounds above 60 °C. The polymerization at 150 °C was too fast to be controlled. The yield and the viscosity number, i gp/c, of the resulting polyamide increased with the reaction time. The initial rate of the polymerization became higher with the size of the countercation, in analogy to the case of anionic polymerization of e-caprolactam59. The rate increased also with raising temperature as shown in Fig. 658. ... 

Styrene Free radical polymerization similar to the above. Also susceptible to rapid cationic polymerization induced by AlCb at —80°C and to anionic polymerization using alkali metals or their hydrides —CH2—CH— (ieHs T = 100 Amorphous, even when stretched. Hard. Soluble in aromatic hydrocarbons, higher ketones, and esters... 

Preparation and Reactions of S-b-MM. As mentioned in the introduction, we were interested in block copolymers of styrene and alkali metal methacrylates with overall molecular weights of about 20,000 and methacrylate contents on the order of 10 mol%. The preparation of such copolymers by the usual anionic techniques is not feasible. An alternative is to prepare block copolymers of styrene and methacrylic esters by sequential anionic polymerization, followed by a post-polymerization reaction to produce the desired block copolymers. The obvious first choice of methacrylic esters is methyl methacrylate. It is inexpensive, readily available, and its block copolymers with styrene are well-known. In fact, Brown and White have reported the preparation and hydrolyses of a series of S-b-MM copolymers of varying MM content using p-toluenesulfonic acid (TsOH) (6). The resulting methacrylic acid copolymers were easily converted to their sodium carboxylates by neutralization with sodium hydroxide. 

Anionic polymerization of 1,3-disilacyclobutanes also is possible. Solid KOH and alkali metal silanolates were mentioned as being effective by Russian authors [18, 19. 20]. However, alkyllithiums, which can initiate polymerization of silacyclobutanes (eq. 8) [21], do not initiate polymerization of 1,3-disilacyclobutanes [18, 22]. The problem is one of steric hindrance. 

Another differential reaction is copolymerization. An equi-molar mixture of styrene and methyl methacrylate gives copolymers of different composition depending on the initiator. The radical chains started by benzoyl peroxide are 51 % polystyrene, the cationic chains from stannic chloride or boron trifluoride etherate are 100% polystyrene, and the anionic chains from sodium or potassium are more than 99 % polymethyl methacrylate.444 The radicals attack either monomer indiscriminately, the carbanions prefer methyl methacrylate and the carbonium ions prefer styrene. As can be seen from the data of Table XIV, the reactivity of a radical varies considerably with its structure, and it is worth considering whether this variability would be enough to make a radical derived from sodium or potassium give 99 % polymethyl methacrylate.446 If so, the alkali metal intitiated polymerization would not need to be a carbanionic chain reaction. However, the polymer initiated by triphenylmethyl sodium is also about 99% polymethyl methacrylate, whereas tert-butyl peroxide and >-chlorobenzoyl peroxide give 49 to 51 % styrene in the initial polymer.445... 

The currently accepted mechanism of the alkali metal-mediated Wurtz-type condensation of dichlorosilanes is essentially that outlined in COMC II (1995) (chapter Organopolysilanes, p 98) which derived from studies by Gautier and Worsfold,42 and the groups of Matyjaszewski43 and Jones,22,44,45 a modified polymerization scheme of which is included here. The mechanism was deduced from careful observations on the progress of polymerizations in different solvents (such as those which better stabilize anions and those which do not), at different temperatures,44 with additives, and with different alkali metal reductants. Silyl anions, silyl anion radicals,42 and silyl radicals28,46,47 are believed to be involved, as shown in Scheme 3. 

Block copolymers of (R,S)-(3-butyrolactone and eCL have been synthesized by combining the anionic ROP of the first monomer with the coordinative ROP of the second one (Scheme 15) [71]. The first step consisted of the synthesis of hydroxy-terminated atactic P(3BL by anionic polymerization initiated by the alkali-metal salt of a hydroxycarboxylic acid complexed with a crown ether. The hydroxyl end group of P(3BL could then be reacted with AlEt3 to form a macroinitiator for the eCL ROP. 

---