Adhesion transition

An urgent problem of theoretical investigations seems to be tte search for specific unsteady-state solutions oscillating, chaotic, etc., based cki rteokit tic reasoning. One of the possible alternatives for initiation of oscillating states of motion for tlieo-kinetic media the sliding — adhesion transition which was discussed in Ref. [110]. 

Effect of changing the debonding velocity cohesive to adhesive transition... 

Elastomeric Modified Adhesives. The major characteristic of the resins discussed above is that after cure, or after polymerization, they are extremely brittie. Thus, the utility of unmodified common resins as stmctural adhesives would be very limited. Eor highly cross-linked resin systems to be usehil stmctural adhesives, they have to be modified to ensure fracture resistance. Modification can be effected by the addition of an elastomer which is soluble within the cross-linked resin. Modification of a cross-linked resin in this fashion generally decreases the glass-transition temperature but increases the resin dexibiUty, and thus increases the fracture resistance of the cured adhesive. Recendy, stmctural adhesives have been modified by elastomers which are soluble within the uncured stmctural adhesive, but then phase separate during the cure to form a two-phase system. The matrix properties are mosdy retained the glass-transition temperature is only moderately affected by the presence of the elastomer, yet the fracture resistance is substantially improved. 

This type of adhesive is generally useful in the temperature range where the material is either leathery or mbbery, ie, between the glass-transition temperature and the melt temperature. Hot-melt adhesives are based on thermoplastic polymers that may be compounded or uncompounded ethylene—vinyl acetate copolymers, paraffin waxes, polypropylene, phenoxy resins, styrene—butadiene copolymers, ethylene—ethyl acrylate copolymers, and low, and low density polypropylene are used in the compounded state polyesters, polyamides, and polyurethanes are used in the mosdy uncompounded state. 

In the area of moleculady designed hot-melt adhesives, the most widely used resins are the polyamides (qv), formed upon reaction of a diamine and a dimer acid. Dimer acids (qv) are obtained from the Diels-Alder reaction of unsaturated fatty acids. Linoleic acid is an example. Judicious selection of diamine and diacid leads to a wide range of adhesive properties. Typical shear characteristics are in the range of thousands of kilopascals and are dependent upon temperature. Although hot-melt adhesives normally become quite brittle below the glass-transition temperature, these materials can often attain physical properties that approach those of a stmctural adhesive. These properties severely degrade as the material becomes Hquid above the melt temperature. 

Plasticizers and Processing Aids. Petroleum-based oils are commonly used as plasticizers. Compound viscosity is reduced, and mixing, processing, and low temperature properties are improved. Air permeabihty is increased by adding extender oils. Plasticizers are selected for their compatibihty and low temperature properties. Butyl mbber has a solubihty parameter of ca 15.3 (f /cm ) [7.5 (cal/cm ) ], similar to paraffinic and naphthenic oils. Polybutenes, paraffin waxes, and low mol wt polyethylene can also be used as plasticizers (qv). Alkyl adipates and sebacates reduce the glass-transition temperature and improve low temperature properties. Process aids, eg, mineral mbber and Stmktol 40 ms, improve filler dispersion and cured adhesion to high unsaturated mbber substrates. 

Because of increased production and the lower cost of raw material, thermoplastic elastomeric materials are a significant and growing part of the total polymers market. World consumption in 1995 is estimated to approach 1,000,000 metric tons (3). However, because the melt to soHd transition is reversible, some properties of thermoplastic elastomers, eg, compression set, solvent resistance, and resistance to deformation at high temperatures, are usually not as good as those of the conventional vulcanized mbbers. AppHcations of thermoplastic elastomers are, therefore, in areas where these properties are less important, eg, footwear, wine insulation, adhesives, polymer blending, and not in areas such as automobile tires. 

Poly(vinyl acetate) is too soft and shows excessive cold flow for use in moulded plastics. This is no doubt associated with the fact that the glass transition temperature of 28°C is little above the usual ambient temperatures and in fact in many places at various times the glass temperature may be the lower. It has a density of 1.19 g/cm and a refractive index of 1.47. Commercial polymers are atactic and, since they do not crystallise, transparent (if free from emulsifier). They are successfully used in emulsion paints, as adhesives for textiles, paper and wood, as a sizing material and as a permanent starch . A number of grades are supplied by manufacturers which differ in molecular weight and in the nature of comonomers (e.g. vinyl maleate) which are commonly used (see Section 14.4.4)... 

---