Addition polymers physical properties

Though both miscible and immiscible blends are composite materials, their properties are very different. A miscible blend will exhibit a single glass transition temperature that is intermediate between those of the individual polymers. In addition, the physical properties of the blends will also exhibit this intermediate behavior. Immiscible blends, on the other hand, still contain discrete phases of both polymers. This means that they have two glass transition temperatures and that each represents one of the two components of the blend. (A caveat must be added here in that two materials that are immiscible with very small domain sizes will also show a single, intermediate value for Tg.) In addition, the physical properties... 

A basic formulation requires there to be a majority of polymer with additives provided as minor ingredients. By manipulating a basic range of additives, the physical properties of the compound can be improved. The type and level of addition of additives should be based on the degree of performance contributed per unit of addition, with an optimum level required to give maximum performance, even under the most adverse conditions, while considering the cost of achieving these performance levels. 

The requirements for the backing space structures are that they should be light in weight and have high specific strength and stiffness in addition, their physical properties must be able to resist the hostile environments of space. Polymer composites have the required mechanical and in-service attributes and, if necessary, the polymers can be modified to provide properties to resist the hostile space environments for a finite length of time. 

Particulate additive, designed to change polymer physical properties (e.g. fire resistance, modulus, shock resistance) or to lower cost. 

Preliminary conductivity results indicate that I2-doped thin films (0.5-4 fxm) of polymers 13 and 15 exhibit electrical conductivities in the range of 50-200 S/ cm [76]. In addition, the physical properties of these polymers are unchanged over number average molecular weights (A/ ) ranging from 9000 to 28,000 (PDI = 1,6). Therefore, these properties appear not to be a function of the molecular weight of the polymer. 

Characterisation of polymer blends and the effect of additives on physical properties 220... 

Mention has already been made in Section 6.3.2 of how the high sensitivity of DMA to the glass transition of polymers can be used to characterise polymer blends and investigate the effect of additives on physical properties. 

The polymeric products can be made to vary widely in physical properties through controlled variation in the ratios of monomers employed in thek preparation, cross-linking, and control of molecular weight. They share common quaHties of high resistance to chemical and environmental attack, excellent clarity, and attractive strength properties (see Acrylic ester polymers). In addition to acryHc acid itself, methyl, ethyl, butyl, isobutyl, and 2-ethylhexyl acrylates are manufactured on a large scale and are available in better than 98—99% purity (4). They usually contain 10—200 ppm of hydroquinone monomethyl ether as polymerization inhibitor. 

Other. A large variety of additives are used in paper-coatiag colors primarily to modify the physical properties of the colors (102). At high soHds concentrations in water, mineral pigment particles tend to associate and form viscous pastes. Dispersants (qv) are used to prevent this and to provide low viscosity slurries. Common dispersants include polyphosphates and sodium polyacrylate [9003-04-7]. Various water-soluble polymers are added to coatiag colors and act as water-retention agents and as rheology modifiers. 

PVC. Poly(vinyl chloride) (PVC), a very versatile polymer, is manufactured by the polymerisation of vinyl chloride monomer, a gaseous substance obtained from the reaction of ethylene with oxygen and hydrochloric acid. In its most basic form, the resin is a relatively hard material that requites the addition of other compounds, commonly plasticisers and stabilisers as well as certain other ingredients, to produce the desired physical properties for roofing use. The membranes come in both reinforced and nonreinforced constmctions, but since the 1980s the direction has been toward offering only reinforced membranes. The membrane thickness typically mns from 0.8—1.5 mm and widths typically in the range of 1.5—4.6 m. 

Nearly all polymeric materials require the addition of antioxidants to retain physical properties and to ensure an adequate service life. The selection of an antioxidant or system of antioxidants is dependent upon the polymer and the anticipated end use. A product that will not be exposed to the elements for a long period of time such as polyethylene grocery bags does not need a long term stabilizer polyethylenes used to iasulate communication cable must be stabilized for many years of service. 

The carbon blacks used in plastics are usually different from the carbon blacks used in mbber. The effect of carbon black is detrimental to the physical properties of plastics such as impact strength and melt flow. Electroconductive grades of carbon black have much higher surface areas than conventional carbon blacks. The higher surface areas result in a three-dimensional conductive pathway through the polymer at much lower additive levels of the carbon black. The additive concentrations of electroconductive carbon blacks is usually j to that of a regular carbon black (132). 

Radiopaque materials are used to determine the location of aspirated dentures and fragments (205,206). Opacifying additives include barium sulfate, barium fluoride, barium or bismuth glasses, and brominated organic monomers and polymers. The incorporation of these additives into the resin base or tooth can adversely affect physical properties. Radiopaque materials meeting the requirement for ANSI/ADA specifications for denture-base polymer have been described (207). 

---