Initiator activation energy

It is, however, possible to induce explosions in these systems by the use of additives which are frequently referred to as sensitizers. Thus Ashmore has shown that the addition of 0.5 mm Ilg of NO to 50 mm Ilg of an equimolar mixture of H2 + CI2 lowers the critical explosion temperature from 400 to 270°C. The explosion in this case is still, however, a thermal explosion, and it has been shown that the lowering of the explosion temperature was produced by an increase in the concentration of Cl atoms, not by a change in the chain mechanism. This increase in concentration of Cl atoms was produced by the replacement of the slow, high-activation-energy initiation reaction, M + CI2 2C1 + M(E > 57 Real), by the much-lower-activation-energy reaction, NO + CI2 NOCl + C1(jE = 22 Real). 

C, constant E, activation energy Initial stages of cure... 

E, viscous activation energy initial viscosity Reaction and gel effects with no phase separation. k, constant... 

E f i, /- l,n ktj activation energy initiation efficiency degree of polymerization length and number of segments in polymer zwitterion termination rate constant of radicals Rj and Rj... 

Somewhat different behaviour has been found when Group 11 metals are added to platinum and palladium. Activities fall continuously, and activation energy initially, but the former is determined subsequently by the decrease in the pre-exponential factor (Figure 10.7). Activities were also increased by adding molybdenum, rhenium - or iridium to platinum. There are conflicting... 

The activation energy, is defined as tlie minimum additional energy above the zero-point energy that is needed for a system to pass from the initial to the final state in a chemical reaction. In tenns of equation (A2.4.132). the energy of the initial reactants at v = v is given by... 

Table 6.2 Rate Constants (at Temperature Given) and Activation Energies for Some Initiator Decomposition Reactions...

The activation energies for the decomposition (subscript d) reaction of several different initiators in various solvents are shown in Table 6.2. Also listed are values of k for these systems at the temperature shown. The Arrhenius equation can be used in the form ln(k j/k j) (E /R)(l/Ti - I/T2) to evaluate k j values for these systems at temperatures different from those given in Table 6.2. 

Using typical activation energies out of Tables 6.2-6.4, estimate the percent change in the rate of polymerization with a 1°C change in temperature at 50°C for thermally initiated and photinitiated polymerization. 

For photoinitiation there is no activation energy for the initiator decomposition hence... 

The two possible initiations for the free-radical reaction are step lb or the combination of steps la and 2a from Table 1. The role of the initiation step lb in the reaction scheme is an important consideration in minimising the concentration of atomic fluorine (27). As indicated in Table 1, this process is spontaneous at room temperature [AG25 = —24.4 kJ/mol (—5.84 kcal/mol) ] although the enthalpy is slightly positive. The validity of this step has not yet been conclusively estabUshed by spectroscopic methods which makes it an unsolved problem of prime importance. Furthermore, the fact that fluorine reacts at a significant rate with some hydrocarbons in the dark at temperatures below —78° C indicates that step lb is important and may have Httie or no activation energy at RT. At extremely low temperatures (ca 10 K) there is no reaction between gaseous fluorine and CH or 2 6... 

Activation Parameters. Thermal processes are commonly used to break labile initiator bonds in order to form radicals. The amount of thermal energy necessary varies with the environment, but absolute temperature, T, is usually the dominant factor. The energy barrier, the minimum amount of energy that must be suppHed, is called the activation energy, E. A third important factor, known as the frequency factor, is a measure of bond motion freedom (translational, rotational, and vibrational) in the activated complex or transition state. The relationships of yi, E and T to the initiator decomposition rate (kJ) are expressed by the Arrhenius first-order rate equation (eq. 16) where R is the gas constant, and and E are known as the activation parameters. 

Because the chemiluminescence intensity can be used to monitor the concentration of peroxyl radicals, factors that influence the rate of autooxidation can easily be measured. Included are the rate and activation energy of initiation, rates of chain transfer in cooxidations, the activities of catalysts such as cobalt salts, and the activities of inhibitors (128). 

Volumetric heat generation increases with temperature as a single or multiple S-shaped curves, whereas surface heat removal increases linearly. The shapes of these heat-generation curves and the slopes of the heat-removal lines depend on reaction kinetics, activation energies, reactant concentrations, flow rates, and the initial temperatures of reactants and coolants (70). The intersections of the heat-generation curves and heat-removal lines represent possible steady-state operations called stationary states (Fig. 15). Multiple stationary states are possible. Control is introduced to estabHsh the desired steady-state operation, produce products at targeted rates, and provide safe start-up and shutdown. Control methods can affect overall performance by their way of adjusting temperature and concentration variations and upsets, and by the closeness to which critical variables are operated near their limits. 

Polymerization Solvent. Sulfolane can be used alone or in combination with a cosolvent as a polymerization solvent for polyureas, polysulfones, polysUoxanes, polyether polyols, polybenzimidazoles, polyphenylene ethers, poly(l,4-benzamide) (poly(imino-l,4-phenylenecarbonyl)), sUylated poly(amides), poly(arylene ether ketones), polythioamides, and poly(vinylnaphthalene/fumaronitrile) initiated by laser (134—144). Advantages of using sulfolane as a polymerization solvent include increased polymerization rate, ease of polymer purification, better solubilizing characteristics, and improved thermal stabUity. The increased polymerization rate has been attributed not only to an increase in the reaction temperature because of the higher boiling point of sulfolane, but also to a decrease in the activation energy of polymerization as a result of the contribution from the sulfonic group of the solvent. 

The transition is fully classical and it proceeds over the barrier which is lower than the static one, Vo = ntoColQl- Below but above the second cross-over temperature T 2 = hcoi/2k, the tunneling transition along Q is modulated by the classical low-frequency q vibration. The apparent activation energy is smaller than V. The rate constant levels off to its low-temperature limit k only at 7 < Tc2, when tunneling starts out from the ground state of the initial parabolic term. The effective barrier in this case is neither V nor Vo,... 

The polycyclic aromatic hydrocarbons such as naphthalene, anthracene, and phenan-threne undergo electrophilic aromatic substitution and are generally more reactive than benzene. One reason is that the activation energy for formation of the c-complex is lower than for benzene because more of the initial resonance stabilization is retained in intermediates that have a fused benzene ring. 

---