Ziegler Natta isotactic

Figure 11 Left Spherulites of a Ziegler-Natta isotactic poly(propylene) with Mw = 271,500 g/mol and mmmm — 0.95, isothermally crystallized at 148°C. Right Banded spherulites of a linear polyethylene with Mw = 53,600 g/mol slowly cooled from the melt.

Figure 17 Isothermal melting of Ziegler-Natta isotactic poly(propylene). (a) Spherulites with mixed birefringence at Tc = 148°C. The top middle figure displays the melting for the same thermal history, (b) Subsequent to crystallization, the temperature was raised to 171°C spherulites acquire negative birefringence, (c), (d) and (e) Isothermal melting at 171°C for 80, 200 and 300 min, respectively. Reproduced with permission from W.T. Huang, Dissertation, Florida State University, 2005. (See Color Plate Section at the end of this book.)...

Studies of the reactions of propylene and alpha-olefins show that the Ziegler-Natta isotactic polymerizations are between the highly cationic and mildly anionic catalysts. 

C solid-state NMR spectra were recorded for metallocene and Ziegler-Natta isotactic polypropylenes using VT CPMAS. In addition relaxation measurements were undertaken to exam the dynamics of the polymers. 

Randall, J. C. Alamo, R. G Agarwal, P. K. Ruff, C. J. Crystallization rates of matched fractions of MgCl2-supported Ziegler-Natta and metallocene isotactic poly(propylene)s. 2. Chain microstructures from a supercritical fluid fractionation of a MgCl2-supported Ziegler-Natta isotactic poly(propylene). 

When propene is polymerized under free radical conditions the polypropylene that results IS atactic Catalysts of the Ziegler-Natta type however permit the preparation of either isotactic or syndiotactic polypropylene We see here an example of how proper choice of experimental conditions can affect the stereochemical course of a chemical reaction to the extent that entirely new materials with unique properties result... 

Erom 1955—1975, the Ziegler-Natta catalyst (91), which is titanium trichloride used in combination with diethylaluminum chloride, was the catalyst system for propylene polymerization. However, its low activity, which is less than 1000 g polymer/g catalyst in most cases, and low selectivity (ca 90% to isotactic polymer) required polypropylene manufacturers to purify the reactor product by washing out spent catalyst residues and removing unwanted atactic polymer by solvent extraction. These operations added significantly to the cost of pre-1980 polypropylene. 

Polypropylene made by free-radical polymerization is generally atactic , that is to say, there is no pattern to the stereochemistry. On the other hand, both isotactic polypropylene (in which all the stereocenters are the same) and syndiotactic polypropylene (in which the stereocenters alternate) may be made via the Ziegler-Natta process (see Chapter 18, Problem 4). Experimentally, both isotactic and syndiotactic polypropylene generally have higher melting points than atactic polypropylene. 

The three different stereochemical forms of polypropylene all have somewhat different properties, and all can be made by using the right polymerization catalyst. Propylene polymerization using radical initiators does not work well, but polymerization using Ziegler-Natta catalysts allows preparation of isotactic, syndiotactic, and atactic polypropylene. 

Following their introduction in 1953, Ziegler-Natta catalysts revolutionized the field of polymer chemistry because of two advantages the resultant polymers are linear, with practically no chain branching, and they are stereochemical ly controllable. Isotactic, syndiotactic, and atactic forms can all be produced, depending on the catalyst system used. 

Alkene polymerization can be carried out in a controlled manner using a Ziegler-Natta catalyst. Ziegler-Natta polymerization minimizes the amount of chain branching in the polymer and leads to stereoregular chains—either isotactic (substituents on the same side of the chain) or syndiotactic (substituents on alternate sides of the chain), rather than atactic (substituents randomly disposed). 

Polypropylene grades manufactured using Ziegler-Natta catalysts are predominandy isotactic, with a comparatively broad molecular weight distribution (Afw/Mn 3.5). Ziegler-Natta catalyzed polypropylene comprises the majority of commodity grade resins. 

We can employ coordination polymerization to produce stereoregular polystyrene. By performing this type of reaction at low temperatures, using Ziegler-Natta or single-site catalysts, we can prepare isotactic and syndiotactic versions of polystyrene. 

Ziegler-Natta catalysts are used commercially for the production of stereoregular polymers, especially isotactic polypropylene and high-density linear polyethylene. The resultant polymers have number and weight average molecular weights (Mn and Mw, respectively) that are defined as... 

Both syndiotactic and isotactic polypropylene have been made using Ziegler-Natta catalysts. 

---