Wrapped

In the internal gravel pack shown, carefully sorted sand grains, called gravel, are placed between a wire wrapped screen and the perforations with the objective of stopping... 

A ring specimen is cut from the tube. Two coils are wrapped around this ring, one exciter coil and one receiver coil. The exciter coil N1 should cover the entire ring so that there are no field losses when ring is saturated. The sinusoidal exciter current which can be measured at... 

It is best now to proceed as in the Skraup Synthesis (p. 297) and warm the mixture over an asbestos-covered gauze with a Bunsen flame until the reaction starts, and have at hand a duster soaked in cold water so that when the reaction starts, the heating can be at once removed and the duster wrapped round the shoulders of the flask to aid condensation. 

The blanket when required should be at once wrapped firmly around the person whose clothes are on fire, the person then placed m a prone position on the floor with the ignited portion upwards, and water poured freely both over the blanket and in between the blanket and the person s clothes until the fire is extinguished. 

It should then be softened by rolhng in a cork press or by wrapping it in paper and roUing under the foot. 

If the iodide is deeply coloured, it may be decolourised with a little sodium bisulphite. A perfecUy colourless product can be obtained by distilling in the dark or in dilfusod light from a little silver powder. The iodide should be preserved in a bottle containing a short coil of copper wire made by wrapping coppor wire round a glass rod or tube. 

The yield of iso-propylbenzene is influenced considerably by the quality of the anhydrous aluminium chloride employed. It Is recommended that a good grade of technical material be purchase in small bottles containing not more than 100 g. each undue exposure to the atmosphere, which results in some hydrolysis, is thus avoided. Sealed bottles containing the reagent sometimes have a high internal pressure they should be wrapped in a dry cloth and opened with care. 

Preparation of benzyl cyanide. Place 100 g. of powdered, technical sodium cyanide (97-98 per cent. NaCN) (CAUTION) and 90 ml. of water in a 1 litre round-bottomed flask provided with a reflux condenser. Warm on a water bath until the sodium cyanide dissolves. Add, by means of a separatory funnel fitted into the top of the condenser with a grooved cork, a solution of 200 g. (181-5 ml.) of benzyl chloride (Section IV.22) in 200 g. of rectified spirit during 30-45 minutes. Heat the mixture in a water bath for 4 hours, cool, and filter off the precipitated sodium chloride with suction wash with a little alcohol. Distil off as much as possible of the alcohol on a water bath (wrap the flask in a cloth) (Fig. II, 13, 3). Cool the residual liquid, filter if necessary, and separate the layer of crude benzyl cyanide. (Sometimes it is advantageous to extract the nitrile with ether or benzene.) Dry over a little anhydrous magnesium sulphate, and distil under diminished pressure from a Claisen flask, preferably with a fractionating side arm (Figs. II, 24, 2-5). Collect the benzyl cyanide at 102-103°/10 mm. The yield is 160 g. 

In a 500 ml. conical flask place 50 ml. of glachtl acetic acid, 25 ml. of 40 per cent, formaldehyde solution (formalin) and 20 g. of phenol. Wrap a cloth or towel loosely around the neck and opening of the flask. Pass dry hydrogen chloride gas (Section 11,48,1) into the mixture. Within 5 minutes, a large mass of pink plastic is formed the reaction is sometimes very vigorous. The yield is 36 g. It is frequently necessary to break the flask in order to remove the product completely for this reason a beaker, or metal flask or beaker, is preferable. 

Burning clothing. Prevent the person from running and fanning the flames. Make the victim he down on the floor, or throw him (her) down if necessary, and wrap the fireproof blanket firmly around the ignited clothes until the fire is extinguished. 

All of the pieces pictured here are not going to fit perfectiy into each other and that s going to cause all sorts of leaks. The answer is teflon tape. Strike loves teflon tape This inexpensive product is found in the plumbing department of any hardware store and is the duct tape of the next century. Teflon tape is chemically and thermally indestructible. This stuff is wrapped around any piece of pipe or joint, said part then jammed into its appropriate receptacle and the tape will mold to form a perfect fit. Hell, it can mummify a whoie joint compiex to make it absolutely impregnable. 

Another thing or two to remember when distilling is to wrap aluminum foil around the reaction flask. This will help stop heat loss so that things will distill quicker and at lower temperatures. Sometimes, if one is going to distill a solution that is just solvent and product, all that pure solvent that comes over first is perfectly reusable and should be saved for future extractions. 

You see that vacuum adapter stuck to the top of the condenser in fig. 7a Well, a closer look at it in fig. 7b will show that it has some drying agent sandwiched between two cotton balls and the nipple (tee heel) sealed with plastic wrap or foil. The drying agent can be either a commercial product called Drierite or calcium chloride. This attachment is placed on top of a condenser when refluxing solutions that have no water in them and must remain that way during the time they are refluxed. All this is to prevent moisture in the outside air from coming into contact with the cold surface of the of the inside walls of the condenser. This will surely happen and the condensed outside-air water will drip down into the reaction flask and ruin the experiment. This is not so much a... 

Aluminum foil (to wrap flask still head-insulation)... 

Set-up for vac-distillation. She wraps the flask and still head with aluminum foil to act as an insulator. Speeds up the distillation process. Begin to heat the DCM extraction slowly under maximum... 

Cut the blanched bacon strips in half. Place one jalapeno half against 1 shrimp, wrap with a bacon piece and secure with a toothpick. Place all of the shrimp brochettes into a bowl and marinated at least 30 minutes covered with teriyaki sauce. Broil 5 minutes and serve. Yum ... 

The sequence of amino acids in a peptide can be written using the three-letter code shown in Figure 45.3 or a one-letter code, both in common use. For example, the tripeptide, ala.ala.phe, could be abbreviated further to AAF Although peptides and proteins have chain-like structures, they seldom produce a simple linear system rather, the chains fold and wrap around each other to give complex shapes. The chemical nature of the various amino acid side groups dictates the way in which the chains fold to arrive at a thermodynamically most-favored state. 

---