Water-assisted injection molding

Liu, S.-J. Chen, Y.-S. Water-assisted injection molding of thermoplastic materials effects of processing parameters. Polym. Eng. Sci. 2003, 43, 1806-1817. [Pg.1409]

S.-J. liu, W.-R. Lin, K.-Y. Lin, Morphological development in water assisted injection molded polyethylene/polyamide-6 blends. Polym. Adv. Technol. 22, 2062-2068 (2011)... [Pg.152]

Scanning electron micrographs (SEMs) of (a) inner layer, (b) core region, and (c) outer layer at two positions of water-assisted injection-molded polypropylene (PP)/polyamide-6 (PA-6) blend. Water pressure, 10 MPa melt temperature, 270°C injection speed, 50%. (Reproduced from Huang, H.-X., and Zhou, R.-H. 2010. Preliminary investigation on morphology in water-assisted injection molded polymer blends. Polymer Testing 29 235-244 with permission from Elsevier.)... [Pg.20]

Huang, H.-X., and Zhou, R.-H. 2010. Rreliminary investigation on morphology in water-assisted injection molded polymer blends. Polymer Testing 29 235-244. [Pg.25]

S. J. Liu and Y. S. Chen, The manufacture of thermoplastic composites by water assisted injection molding technology. Composites Part A Applied Science and Manufacture, 35,171—180 (2004). [Pg.42]

S. J. Liu and C. C. Shih, Water assisted injection molding of glass fiber reinforced Nylon-6 composites, Journal of Reinforced Plastics and Composites, 27, 985-999 (2008). [Pg.43]

S. J. Liu, M. J. Lin and Y. C. Wu, An experimental study of the water-assisted injection molding of glass fiber filled polybutylene terephthalate (PBT) composites, Composites Science and Technology, 67,1415-1424 (2007). [Pg.43]

S. J. Liu, Water assisted injection molding areview. International Polymer Processing, 14, 315-325 (2009). [Pg.43]

There are different gas-assist injection molding (GAIM) processes. Other names exist that include injection molding gas-assist (IMGA), gas injection molding (GIM), or injection gas pressure (IGP). Most of the gas-assisted molding systems are patented. This review concerns the use of gas, however there are others such as water-assist injection molding. [Pg.36]

Numerical simulation, crystallization, water-assisted injection molding, gas-assisted injection molding. [Pg.267]

DEVELOPMENTS IN WATER ASSISTED INJECTION MOLDING PROCESS... [Pg.1820]

Protte, R., et al. Water-Assist Injection Molding - An Innovative Process Technology for Productivity Improvement Developments in Processing, Equipment, and Materials. SPE ANTEC Proceedings, 0750,2003. [Pg.3016]

PENETRATION LENGTH, THICKNESS AND CRYSTALLIZATION BEHAVIOR OF WATER-ASSISTED INJECTION MOLDED PART... [Pg.3067]

Water-assisted injection molding experiments were carried out on newly developed equipment in our lab. The effects of four processing parameters, short-shot size, melt temperature, water injection delay time, and water pressure, on the water penetration length and residual wall thickness of water-assisted injeetion molded polypropylene curved pipe were investigated. The crystallization behavior difference between the beginning and the end of the water channel of the eurved pipe was analyzed using differential scanning calorimetry. [Pg.3067]

Key words water-assisted injection molding (WAIM), water penetration length, residual wall thickness, crystallization behavior. [Pg.3071]

PREDICTING PROCESSING PARAMETERS FOR WATER-ASSISTED INJECTION MOLDING BASED ON INVERSE GA-LMBP NEURAL NETWORK... [Pg.3077]

Water-assisted injection molding experiments were carried out on newly developed equipment in our lab to investigate the influence of melt temperature, water injeetion pressure, water injection delay time, and short-... [Pg.3078]

Figure 2. Schematic of water-assisted injection molded curved pipe.

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...