Urea/formaldehyde curing

In practice, synthetic polymers are sometimes divided into two classes, thermosetting and thermo-plMtic. Those polymers which in their original condition will fiow and can be moulded by heat and pressime, but which in their finished or cured state cannot be re softened or moulded are known as thermo setting (examples phenol formaldehyde or urea formaldehyde polymer). Thermoplastic polymers can be resoftened and remoulded by heat (examples ethylene polymers and polymers of acrylic esters). 

Both melamine—formaldehyde (MF) and resorcinol—formaldehyde (RF) foUowed the eadier developments of phenol—, and urea—formaldehyde. Melamine has a more complex stmcture than urea and is also more expensive. Melamine-base resins requite heat to cure, produce colorless gluelines, and are much more water-resistant than urea resins but stiU are not quite waterproof. Because of melamine s similarity to urea, it is often used in fairly small amounts with urea to produce melamine—urea—formaldehyde (MUF) resins. Thus, the improved characteristics of melamine can be combined with the economy of urea to provide an improved adhesive at a moderate increase in cost. The improvement is roughly proportional to the amount of melamine used the range of addition may be from 5 to 35%, with 5—10% most common. 

The primary adhesive used ia hardwood plywood is urea—formaldehyde (UF) mixed with wheat flour as an extender to improve spreadabiUty, reduce penetration, and provide dry-out resistance. A catalyst may also be added to UF resias to speed the cure or to cause the UF to cure. Scavengers also may be added to reduce formaldehyde emissions from finished panels. If more water-resistance is requited using a UF bond, small amounts of melamine maybe added, producing a melamine—urea—formaldehyde (MUF) adhesive. 

Urea.—Forma.IdehydeResins. Cellular urea—formaldehyde resins can be prepared in the following manner an aqueous solution containing surfactant and catalyst is made into a low density, fine-celled foam by dispersing air into it mechanically. A second aqueous solution consisting of partially cured urea—formaldehyde resin is then mixed into the foam by mechanical agitation. The catalyst in the initial foam causes the dispersed resin to cure in the cellular state. The resultant hardened foam is dried at elevated temperatures. Densities as low as 8 kg/m can be obtained by this method (117). 

The recovery of fiber from broke (off-specification paper or trim produced in the paper mill) is compHcated by high levels of urea—formaldehyde and melamine—formaldehyde wet-strength resin. The urea resins present a lesser problem than the melamine resins because they cure slower and are not as resistant to hydrolysis. Broke from either resin treatment may be reclaimed by hot acidic repulping. Even the melamine resin is hydrolyzed rapidly under acidic conditions at high temperature. The cellulose is far more resistant and is not harmed if the acid is neutralized as soon as repulping is complete. 

Urea-formaldehyde powders have a limited shelf-life but some improvement is made by incorporating a stabiliser such as hexamine into the moulding power. In some formulations the cure rate and the related time for flow are controlled by keeping the latent acid catalyst fixed and adjusting the stabiliser. 

Urea is sufficiently important as an additive to PF resins for OSB to warrant some discussion. It has had a large favorable economie impact on the OSB industry. When used, it is generally added after the polymerization is complete. Thus, it is not part of the polymer and does not have any direet effect on polymer resistance to hydrolysis, as might be expected if it was part of the polymer backbone. Under alkaline pH conditions, urea-formaldehyde adducts do not polymerize at a rate that is significant compared to the PF polymerization therefore, the urea does not participate signifieantly in the euring proeess of the PF, despite the faet that it is present during the cure. Since urea is not present in the cured PF polymer per se, it does not detract from the durability of the polymer. Despite this, it is possible to see redueed OSB durability as a result of formulated urea if its use has led to actual PF polymer application rates that are too low. 

Urea-formaldehyde resins can be cured with isopropylbenzene production wastes containing 200 to 300 g/liter of AICI3 as an acid hardener [189]. Isopropylbenzene is formed as an intermediate in the Hock process by a Friedel-Crafts reaction from propene and benzene. The mixture hardens in 45 to 90 minutes and develops an adhesion to rock and metal of 0.19 to 0.28 MPa for 0.2% AICI3 and 0.01 to 0.07 MPa for 0.4% AICI3, respectively. A particular advantage is the increased pot life of the formulation. 

Curing of Urea-Formaldehyde and Phenol-Formaldehyde. Urea-formaldehyde resins and phenol-formaldehyde resins can be cured by various mechanisms. 

Acid Curing. Urea-formaldehyde resins and resol-phenol-formaldehyde resins can be acid-cured by wastes from the production of maleic anhydride [1902]. The waste from the production of maleic anhydride contains up to 50% maleic anhydride, in addition to phthalic anhydride, citraconic anhydride, benzoic acid, o-tolulic acid, and phthalide. The plugging solution is prepared by mixing a urea-formaldehyde resin with a phenol-formaldehyde resin, adding the waste from production of maleic anhydride, and mixing thoroughly. 

Urea-formaldehyde resins are used as the main adhesive in the forest product industry because they have a number of advantages, including low cost, ease of use under a wide variety of curing conditions, low cure temperatures, water solubility, resistance to microorganisms and to abrasion, hardness, excellent thermal properties, and a lack of color, especially in the cured resin. 

An acidic-cure catalyst is added to the urea-formaldehyde resin before it is used as an adhesive. Ammonium chloride and ammonium sulfate are the most widely used catalysts for resins in the forest products industry. A variety of other chemicals can be used as a catalyst, including formic acid, boric acid, phosphoric acid, oxalic acid, and acid salts of hexamethylenetetramine. 

---