Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Tubes electric

The product crystals find industrial application as a component raw material for optical glass, fibreglass, Braun tubes, electric condensers, barium ferrite, etc. Needles shaped crystals are obtained at high pH, while pillar-shaped crystals are formed at neutral pH. The formation of carboxyl ions is via hydroxy ions at high pH, but at neutral pH it may accompany the production of hydrogen sulphide, as... [Pg.233]

Valve components, gaskets, tubing electrical insulation... [Pg.11]

Fig. 12. Technician Terry Sickeler adjusts nickel fell between bundles of the tubular solid-oxaJe cells llui[ are central to the generating unit. The conducting felt interconnects the tubes electrically while allowing room for expansion when heated. (Wesrinyhnuse Electric Corporation)... Fig. 12. Technician Terry Sickeler adjusts nickel fell between bundles of the tubular solid-oxaJe cells llui[ are central to the generating unit. The conducting felt interconnects the tubes electrically while allowing room for expansion when heated. (Wesrinyhnuse Electric Corporation)...
The vapor can be atomized in inert gas-hydrogen diffusion flames, in narrow-bore quartz tubes electrically heated or heated over an air-acetylene flame, and in plasmas. Additionally, the atomizer can act as a vapor preconcentration medium just before atomizing. This is what happens in graphite furnace atomizers (in situ trapping) or on silver or gold wires for direct amalgamation of mercury. [Pg.275]

Be Oxide to halide then reduce w/Mg or electrolysis hep 1.85 1278 2970 Neutron moderator, X-ray tubes, electrical equip. [Pg.172]

Platinum can be used in the form of thin sheet or screen. Platinum wire can be welded to a small square of sheet or screen by placing it in position on a metal surface, heating to red heat with a torch, and striking lightly with a small ball peen hammer. The platinum wire can then be sealed into the end of a piece of soft-glass tubing. Electrical contact can be made by copper wire spot-welded to the platinum lead wire before the glass-to-metal seal is made. [Pg.651]

The widest usage of these materials within the chemical process and pharmaceutical industries is for gasket and sealing applications, linings, flexible tubing, electrical insulation, and drive belts. [Pg.794]

Basically, a graphite-furnace atomizer (Fig. 8.1 A) consists of a graphite tube, electrical contacts, an enclosed water-cooled housing and inert purge gas controls. [Pg.349]

Use Break-resistant transparent bottles, packaging films, mercury flasks, protective equipment, pipe and tubing, electric distribution elements. As foam, insulation of fresh concrete. [Pg.698]

The preparation and electrical properties of magnesium mercury, MgjHgj, have been reported. The intermetallic compound was prepared by heating the elements together above 562 °C, at which temperature the compound melts, in an evacuated silica tube. Electrical resistivity and Hall-effect measurements were made from 2.4 to 297 K. No phase transition was observed over this range. The Hall constant was low and the ideal resistivity (the difference between total and residual resistivity) had the form p a T , where a = 1.9 and 1.0 at 11.50K and... [Pg.42]

Solid electrolyte tube Gas filter tube Electric heater... [Pg.428]

Von Wartenbei describes a simple method for obtaining S with a C content of less than 10" %. This procedure requires no special attention and takes place over a period of a few days. A quartz tube, electrically heated to 750°C, is suspended in recrystallized boilii S, thus causing CSg to form on it. When no further black material precipitates on the tube, the sulfur is distilled in vacuum. [Pg.342]

Connect the front drive axle vent tube connecting tube assembly to three ports, the front axle tube, electric clutch and electric clutch housing. [Pg.266]

All pipework and tubes (electricity, water, gasses, air ducts, etc.) should be documented by photographs before the wall is finally closed during construction. Those pictures can demonstrate later that the finished construction indeed does correspond with the as-built drawings. As-built drawings are the drawings that exactly represent the finally built constructive reality. At places where the wall should be loaded with objects to be mounted, the constructor should apply back styles. These are fortifications introduced in the wall,... [Pg.605]

Spangenberg, R. Vacuum tubes. Electrical and electronic engineering series. Me Graw Hill book company Inc., NY, 1948. [Pg.327]

CW welding caps to tubes, electrical terminations and cable joining... [Pg.217]

Many parameters can influence the transformation of polymer solutions into nanofibers through electrospinning. These parameters include (a) solution properties, such as viscosity, elasticity, conductivity and surface tension (b) governing/operating variables, such as hydrostatic pressure in the capillary tube, electric potential at the capillary tip and the gap (distance between the tip and the collecting screen) and (c) ambient parameters such as solution temperature, humidity and air velocity in the electrospinning chamber. ... [Pg.73]


See other pages where Tubes electric is mentioned: [Pg.271]    [Pg.96]    [Pg.494]    [Pg.1136]    [Pg.60]    [Pg.415]    [Pg.149]    [Pg.96]    [Pg.24]    [Pg.83]    [Pg.959]    [Pg.241]    [Pg.313]    [Pg.65]    [Pg.66]    [Pg.1305]    [Pg.590]    [Pg.1306]    [Pg.592]    [Pg.1140]    [Pg.109]    [Pg.60]    [Pg.6]    [Pg.211]    [Pg.66]    [Pg.416]    [Pg.416]    [Pg.197]    [Pg.49]    [Pg.709]    [Pg.542]    [Pg.80]   
See also in sourсe #XX -- [ Pg.599 ]




SEARCH



Drift tube electric field strength

Electric furnace, tube, construction

Electric-discharge tubes

Electrical discharge tube

© 2024 chempedia.info