Transverse measurement

In the special case when a = 0 these measurements can be named as longitudinal, transversally longitudinal, and transverse measurement, respectively. These potentials can be reconstructed directly using the inverse Radon transform (5). 

The integrals are connected with the transversal measurements of the 2-D tensor field (Tij and the 2-D vector field respectively. 

Fig. 6.7 (a) The variation of electrical conductivity of PVA-EG hybrid with increasing graphene content. Inset shows the dependence of dielectric constant for the hybrid, (b) The variation of conductivity of the polystyrene-graphene hybrid with filler content. Inset shows the four probe setup for in-plane and transverse measurements and the computed distributions of the current density for in-plane condition (reference [8]). 

The best way to obtain a thorough grounding in the practical operation of a TLC scanner is to attend a seminar presented by the manufactmer. Only in this way can one really understand the scope and limitations of the equipment and be able to use one s own scaimer in an assured and reliable fashion. The two following Sections give an example of an absorption measurement and a fluorescence measurement respectively, and these are followed by a comparison of a parallel with a transverse measurement. But first we give a few more... 

Mean value height Parallel measurement Transverse measurement... 

Figure 96. Comparison of the direct optical evaluation of sulfamethoxazole and trimethoprim using parallel and transverse measurement at 285 nm using the TLC Scanner III (CAMAG)...

Most of the conductivity measurements were performed on the SPI acidic form since it is the relevant value for the fuel cell application. Nevertheless, a few data were obtained on neutralized forms [141,146,159]. Rollet et al. used sodium and tetramethylammonium ions to study the transport processes within the membranes and a transport anisotropy was clearly observed from longitudinal and transversal measurements [146]. 

In the future, it is expected to be possible to make more routine use of additional wave types, specifically shear or S waves (polarised to horizontal and vertical components) which have a transverse mode of propagation, and are sensitive to a different set of rock properties than P waves. The potential then exists for increasing the number of independent attributes measured in reflection surveys and increasing the resolution of the subsurface image. 

Braun and Hauck [3] discovered that the irrotational and solenoidal components of a 2-D vector field can be imaged separately using the transverse and longitudinal measurements, respectively. This result has a clear analogy in a 2-D tensor field. We can distinguish three types of measurements which determine potentials of the symmetric tensor field separately ... 

From equation (1), we can to observe if the movement is axial the circumference always contained the point (0,0). If the movement is transversal (Eq. 2), the point (0,0) does not belong to the circumference. Therefore, measuring C and R, it is possible to determine the magnitude and direction of the translation. 

Tables I and 2 show the experimental results obtained for axial and transversal displacements respectively, where % is the displacement and Xv. is the displacement measured using our experimental. setup.

Under this programme 25% of the stiffeners and adjacent plate material in bulk carriers will be examined with thickness measurements being taken at upper, lower and mid points in both face and web plates of the stiffeners and associated end brackets. The extent of thickness measurement applied to transverse bulkheads has also been increased. In addition. Classification has revised the scantling requirements for new buildings to nominate thicker material in the bottom structure and at the transverse watertight bulkheads of the No 1 cargo holds. 

In Fig. III-7 we show a molecular dynamics computation for the density profile and pressure difference P - p across the interface of an argonlike system [66] (see also Refs. 67, 68 and citations therein). Similar calculations have been made of 5 in Eq. III-20 [69, 70]. Monte Carlo calculations of the density profile of the vapor-liquid interface of magnesium how stratification penetrating about three atomic diameters into the liquid [71]. Experimental measurement of the transverse structure of the vapor-liquid interface of mercury and gallium showed structures that were indistinguishable from that of the bulk fluids [72, 73]. 

For phase encoding the phase twist is most connnonly varied by incrementing in a series of subsequent transients as tiiis results in a constant transverse relaxation attenuation of the signal at the measurement position. The signal intensity as a fiinction of G is... 

NMR is an important teclnhque for the study of flow and diflfiision, since the measurement may be made highly sensitive to motion without in any way influencing the motion under study. In analogy to many non-NMR-methods, mass transport can be visualized by imaging the distribution of magnetic tracers as a fiinction of time. Tracers may include paramagnetic contrast agents which, in particular, reduce the transverse... 

In electron spin echo relaxation studies, the two-pulse echo amplitude, as a fiinction of tire pulse separation time T, gives a measure of the phase memory relaxation time from which can be extracted if Jj-effects are taken into consideration. Problems may arise from spectral diflfrision due to incomplete excitation of the EPR spectrum. In this case some of the transverse magnetization may leak into adjacent parts of the spectrum that have not been excited by the MW pulses. Spectral diflfrision effects can be suppressed by using the Carr-Purcell-Meiboom-Gill pulse sequence, which is also well known in NMR. The experiment involves using a sequence of n-pulses separated by 2r and can be denoted as [7i/2-(x-7i-T-echo) J. A series of echoes separated by lx is generated and the decay in their amplitudes is characterized by Ty. ... 

The second parameter, tear strength, describes the film resistance to tear propagation. It is measured with a special apparatus, the Ehnendorf Tear Tester (ASTM D1922), and defined as the weight of a loaded pendulum capable of tearing a notched piece of film. Two values are usually measured for each film sample. One determines tear propagation in the machine direction of the film, the other in the transverse direction. 

Tables 4—6 Ust ASTM methods used for the characterization of PB and PMP. A number of specialized methods were developed for testing particular articles manufactured from polyolefins several of these determine the performance of PB and PMP film, including the measurement of the film s dart impact strength and tear strength. Dart impact strength is measured by dropping a heavy dart with a round tip on a stretched film. Tear resistance, which reflects the film s resistance to tear propagation, is measured with the Ehnendorf tear tester. Two values for the tear strength are usually reported, one in the machine dkection of the film and the other in the transverse dkection. Pipes manufactured from PB are tested by pressurizing them internally with water the time-to-burst failure is determined at various temperatures (46). The standard test method for haze and luminous transmittance (ASTM D1003) is used for the measurement of PMP optical characteristics.

Radial density gradients in FCC and other large-diameter pneumatic transfer risers reflect gas—soHd maldistributions and reduce product yields. Cold-flow units are used to measure the transverse catalyst profiles as functions of gas velocity, catalyst flux, and inlet design. Impacts of measured flow distributions have been evaluated using a simple four lump kinetic model and assuming dispersed catalyst clusters where all the reactions are assumed to occur coupled with a continuous gas phase. A 3 wt % conversion advantage is determined for injection feed around the riser circumference as compared with an axial injection design (28). 

Transverse Dimensions or Fineness. Historically, the quantity used to describe the fineness or coarseness of a fiber was the diameter. Eor fibers that have irregular cross-sections or that taper along their lengths, the term diameter has no useful meaning. Eor cylindrical fibers, however, diameter is an accurate measurement of the transverse dimension. Though textile fibers can be purchased in a variety of cross-sectional shapes, diameter is stiU a useful descriptor of the transverse dimension. Eiber diameter is important in determining not only the ease with which fibers can be twisted in converting them to yams, but also fiber stiffness, ie, fabric stiffness, and, alternatively, fabric softness and drapeabiHty. 

---