Transition metal monolayers

Properties of 3d Transition Metal Monolayers on Metal Substrates. 

In the early eighties, a new method for the deposition of transition metal ion monolayer on the surfaces of inorganic oxides was developed in our laboratory [3]. The essential step of this method is the selective reaction of the surface hydroxyl groups with transition metal alkoxide molecules [3,4]. The adopted procedure allows the design of catalysts containing a strictly determined number of transition metal monolayers or sandwich-type catalysts with different metals monolayers anchored to the surface of the carrier. 

The reducibility of platinum should be affected both by SOOI effect (see above) and strong metal-support interaction (SMSI) between platinum and transition metal oxide monolayer. Both mentioned effects were observed by means of temperature-programmed techniques. TPR investigations put in evidence that the reducibility of platinum strongly depended on the type of primary carrier as well as on the type of transition metal monolayer. The results of TPR investigations are presented in Fig. 1 and Table 2. 

The saturation coverage during chemisorption on a clean transition-metal surface is controlled by the fonnation of a chemical bond at a specific site [5] and not necessarily by the area of the molecule. In addition, in this case, the heat of chemisorption of the first monolayer is substantially higher than for the second and subsequent layers where adsorption is via weaker van der Waals interactions. Chemisorption is often usefLil for measuring the area of a specific component of a multi-component surface, for example, the area of small metal particles adsorbed onto a high-surface-area support [6], but not for measuring the total area of the sample. Surface areas measured using this method are specific to the molecule that chemisorbs on the surface. Carbon monoxide titration is therefore often used to define the number of sites available on a supported metal catalyst. In order to measure the total surface area, adsorbates must be selected that interact relatively weakly with the substrate so that the area occupied by each adsorbent is dominated by intennolecular interactions and the area occupied by each molecule is approximately defined by van der Waals radii. This... 

Organosulfur Adsorbates on Metal and Semiconductor Surfaces. Sulfur compounds (qv) and selenium compounds (qv) have a strong affinity for transition metal surfaces (206—211). The number of reported surface-active organosulfur compounds that form monolayers on gold includes di- -alkyl sulfide (212,213), di- -alkyl disulfides (108), thiophenols (214,215), mercaptopyridines (216), mercaptoanilines (217), thiophenes (217), cysteines (218,219), xanthates (220), thiocarbaminates (220), thiocarbamates (221), thioureas (222), mercaptoimidazoles (223—225), and alkaneselenoles (226) (Fig. 11). However, the most studied, and probably most understood, SAM is that of alkanethiolates on Au(lll) surfaces. 

Multilayers of Diphosphates. One way to find surface reactions that may lead to the formation of SAMs is to look for reactions that result in an insoluble salt. This is the case for phosphate monolayers, based on their highly insoluble salts with tetravalent transition metal ions. In these salts, the phosphates form layer stmctures, one OH group sticking to either side. Thus, replacing the OH with an alkyl chain to form the alkyl phosphonic acid was expected to result in a bilayer stmcture with alkyl chains extending from both sides of the metal phosphate sheet (335). When zirconium (TV) is used the distance between next neighbor alkyl chains is - 0.53 nm, which forces either chain disorder or chain tilt so that VDW attractive interactions can be reestablished. 

Raman spectroscopy has provided information on catalytically active transition metal oxide species (e. g. V, Nb, Cr, Mo, W, and Re) present on the surface of different oxide supports (e.g. alumina, titania, zirconia, niobia, and silica). The structures of the surface metal oxide species were reflected in the terminal M=0 and bridging M-O-M vibrations. The location of the surface metal oxide species on the oxide supports was determined by monitoring the specific surface hydroxyls of the support that were being titrated. The surface coverage of the metal oxide species on the oxide supports could be quantitatively obtained, because at monolayer coverage all the reactive surface hydroxyls were titrated and additional metal oxide resulted in the formation of crystalline metal oxide particles. The nature of surface Lewis and Bronsted acid sites in supported metal oxide catalysts has been determined by adsorbing probe mole-... 

The nucleation behavior of transition metal particles is determined by the ratio between the thermal energy of the diffusing atoms and the interaction of the metal atoms at the various nucleation sites. To create very small particles or even single atoms, low temperatures and metal exposures have to be used. The metal was deposited as metal atoms impinging on the surface. The metal exposure is given as the thickness (in monolayer ML) of a hypothetical, uniform, close-packed metal layer. The interaction strength of the metals discussed here was found to rise in the series from Pd < Rh < Co ( Ir) < V [17,32]. Whereas Pd and Rh nucleate preferentially at line defects at 300 K and decorate the point defects at 90 K, point defects are the predominant nucleation center for Co and V at 300 K. At 60 K, Rh nucleates at surface sites between point defects [16,33]. 

There are a number of ways of attaching a monolayer of redox molecules to an electrode surface.10 Multilayered films can be obtained by deposition of a polymer containing redox centers. These may be attached to the polymer backbone covalently, electrostatically, or coordinatively if the redox center contains a transition metal. 

Figure 6. Construction of molecular recognition sites in mesoporous silica. The first step is the formation of close packed monolayers. The second step is the incorporation of a transition metal ions, followed by coordination of the metal ions with the ligands to form host sites that match the shape and size of the targets.

---