Toluene mechanism

Into a 500-ml. bolt head or three-necked fiask, provided with a mechanical stirrer and a reflux condenser, place 60 g. (69 ml.) of thiophene-free toluene (Section 11,47,16) and 60 g. (33 ml.) of concentrated sulphuric acid. Heat the mixture, with stirring, in an oil bath maintained at... 

Bromo-4-aminotoluene, Suspend the hydrochloride in 400 ml, of water in a 1-Utre beaker equipped with a mechanical stirrer. Add a solution of 70 g. of sodium hydroxide in 350 ml. of water. The free base separates as a dark heavy oil. After cooUng to 15-20°, transfer the mixture to a separatory funnel and run off the crude 3-bromo-4-amino-toluene. This weighs 125 g. and can be used directly in the next step (3). 

Equip a 1 litre three-necked flask wdth a reflux condenser, a mechanical stirrer, and a cork carrying a dropping funnel and a thermometer which reaches nearly to the bottom of the flask connect the upper end of the condenser to an absorption trap (Fig. II, 8, 1). Place 100 g. of p-bromo-toluene (Section IV.62) in the flask and immerse the latter in an oil bath (colourless oil in a large beaker). Heat the bath until the temperature of the stirred p-broniotoluene reaches 105°. Illuminate the liquid with... 

Methyl p-toluenesulphonate. This, and other alkyl esters, may be prepared in a somewhat similar manner to the n-butyl ester with good results. Use 500 g. (632 ml.) of methyl alcohol contained in a 1 litre three-necked or bolt-head flask. Add 500 g. of powdered pure p-toluene-sulphonyl chloride with mechanical stirring. Add from a separatory funnel 420 g. of 25 per cent, sodium hydroxide solution drop by drop maintain the temperature of the mixture at 23-27°. When all the alkali has been introduced, test the mixture with litmus if it is not alkaline, add more alkali until the mixture is neutral. Allow to stand for several hours the lower layer is the eater and the upper one consists of alcohol. Separate the ester, wash it with water, then with 4 per cent, sodium carbonate solution and finally with water. Dry over a little anhydrous magnesium sulphate, and distil under reduced pressure. Collect the methyl p-toluenesulphonate at 161°/10 mm. this solidifies on cooling and melts at 28°. The yield is 440 g. 

In a 500 ml. bolt-head flask provided with a thermometer (reaching almost to the bottom) and a calcium chloride (or cotton wool) guard tube, place 100 g. of a-bromo-wo-valerj l bromide and 50 g. of dry, finely-divided urea. Start the reaction by warming the flask on a water bath the temperature soon rises to about 80°. Maintain this temperature for about 3 horns the mass will liquefy and then resolidify. Transfer the sticky reaction product to a large beaker containing saturated sodium bicarbonate solution, stir mechanically and add more saturated sodium bicarbonate solution in small quantities until effervescence ceases. Filter at the pump, suck as dry as possible and dry the crude bromural upon filter paper in the air. RecrystaUise the dry product from toluene. Alternatively, recrystaUise the moist product from hot water (ca. 700 ml.). The yield of pure brommal, m.p. 154-155°, is 28 g. 

Aminopyridine. In a 1 litre three-neoked flask, equipped with a sealed mechanical stirrer, reflux condenser, thermometer and inlet tube for nitrogen, place 300 ml. of dry toluene (1) aud 75 g. of fine granular sodamide (2) bubble a steady stream of nitrogen thi ough the toluene. Stir the mixtiue vigorously and heat the flask in an oil bath until the internal temperatime is 110° (the bath temperatime required is approximately 130°). Add 100 g. of pure dry pyridine (compare Section 11,47,22)... 

If acetoxylation were a conventional electrophilic substitution it is hard to understand why it is not more generally observed in nitration in acetic anhydride. The acetoxylating species is supposed to be very much more selective than the nitrating species, and therefore compared with the situation in (say) toluene in which the ratio of acetoxylation to nitration is small, the introduction of activating substituents into the aromatic nucleus should lead to an increase in the importance of acetoxylation relative to nitration. This is, in fact, observed in the limited range of the alkylbenzenes, although the apparently severe steric requirement of the acetoxylation species is a complicating feature. The failure to observe acetoxylation in the reactions of compounds more reactive than 2-xylene has been attributed to the incursion of another mechan-104... 

Write a stepwise mechanism for the conversion of p-toluene sulfonic acid to p-cresol under the conditions shown in the preceding equation... 

The early kinetic models for copolymerization, Mayo s terminal mechanism (41) and Alfrey s penultimate model (42), did not adequately predict the behavior of SAN systems. Copolymerizations in DMF and toluene indicated that both penultimate and antepenultimate effects had to be considered (43,44). The resulting reactivity model is somewhat compHcated, since there are eight reactivity ratios to consider. 

Synthetic phenol capacity in the United States was reported to be ca 1.6 x 10 t/yr in 1989 (206), almost completely based on the cumene process (see Cumene Phenol). Some synthetic phenol [108-95-2] is made from toluene by a process developed by The Dow Chemical Company (2,299—301). Toluene [108-88-3] is oxidized to benzoic acid in a conventional LPO process. Liquid-phase oxidative decarboxylation with a copper-containing catalyst gives phenol in high yield (2,299—304). The phenoHc hydroxyl group is located ortho to the position previously occupied by the carboxyl group of benzoic acid (2,299,301,305). This provides a means to produce meta-substituted phenols otherwise difficult to make (2,306). VPOs for the oxidative decarboxylation of benzoic acid have also been reported (2,307—309). Although the mechanism appears to be similar to the LPO scheme (309), the VPO reaction is reported not to work for toluic acids (310). 

Epichlorohydrin Elastomers without AGE. Polymerization on a commercial scale is done as either a solution or slurry process at 40—130°C in an aromatic, ahphatic, or ether solvent. Typical solvents are toluene, benzene, heptane, and diethyl ether. Trialkylaluniinum-water and triaLkylaluminum—water—acetylacetone catalysts are employed. A cationic, coordination mechanism is proposed for chain propagation. The product is isolated by steam coagulation. Polymerization is done as a continuous process in which the solvent, catalyst, and monomer are fed to a back-mixed reactor. Pinal product composition of ECH—EO is determined by careful control of the unreacted, or background, monomer in the reactor. In the manufacture of copolymers, the relative reactivity ratios must be considered. The reactivity ratio of EO to ECH has been estimated to be approximately 7 (35—37). 

An interesting reaction occurs when the dihydropyrazine (102 R = CHaPh) is pyrolyzed under vacuum. Toluene is liberated to give the monobenzylpyrazine (103) in high yield, presumably by a radical mechanism. 

In some cases, the exponent is unity. In other cases, the simple power law is only an approximation for an actual sequence of reactions. For instance, the chlorination of toluene catalyzed by acids was found to have CL = 1.15 at 6°C (43°F) and 1.57 at 32°C (90°F), indicating some complex mechanism sensitive to temperature. A particular reaction may proceed in the absence of catalyst out at a reduced rate. Then the rate equation may be... 

A. 2-f2-Bmmoetkyl)-l,3-diozane (1), A 2-L, three-necked flask Is equipped with a mechanical stirrer, thermometer, and gas Inlet tube. In the flask are placed 750 ml of dichloromethane, 112 g (2.00 moll of acrolein (Note 1), and 0.10 g of didnnamalacetone Indicator (Note 2) under nitrogen. The yellow solution is cooled to 0-5°C with an Ice bath. Gaseous hydrogen bromide (Note 3) is bubbled Into the solution with stirring until the Indicator becomes deep red (Note 4). The Ice bath is removed and 1.0 g of p-toluene-sulfonic acid monohydrate and 152.2 g (2.00 mol, 144 mL) of 1,3-propanediol (Note 11 are added. The yellow solution is stirred at room temperature for 8... 

Some other inhibitors from the patent literature include hydroquinone [129], ionoP [130], and quinone [131]. Other inhibitors used to stabilize MMA include butylated hydroxy toluene (BHT), phenothiazine, methylene blue, hydroxy-diphenylamine and di-/jc/<3-napthol [132]. Several good reviews of inhibition and inhibitors have been written [133-136]. The mechanisms of inhibition are subtle and complicated. For example, it has been reported that highly purified benzo-quinone acts as a retarder rather than an inhibitor [137]. It has been proposed... 

---