Thermorheologically simple material time-temperature superposition

Materials to which time-temperature superposition is applicable, are sometimes termed thermorheologically simple materials. The amount of shift, log aT, which is required to bring measurements at a given temperature, T, into superposition with measurements at a reference temperature, Tr, is described, usually within a range of temperatures Tg < T < (Tg + 100), by the WLF equation (6) ... 

Many amorphous homopolymers and random copolymers show thermorheologically simple behavior within the usual experimental accuracy. Plazek (23,24), however, found that the steady-state viscosity and steady-state compliance of polystyrene cannot be described by the same WLF equation. The effect of temperature on entanglement couplings can also result in thermorheologically complex behavior. This has been shown on certain polymethacrylate polymers and their solutions (22, 23, 26, 31). The time-temperature superposition of thermorheologically simple materials is clearly not applicable to polymers with multiple transitions. The classical study in this area is that by Ferry and co-workers (5, 8) on polymethacrylates with relatively long side chains. In these the complex compliance is the sum of two contributions with different sets of relaxation mechanisms the compliance of the chain backbone and that of the side chains, respectively. 

Since the relaxation mechanisms characteristic of the constituent blocks will be associated with separate distributions of relaxation times, the simple time-temperature (or frequency-temperature) superposition applicable to most amorphous homopolymers and random copolymers cannot apply to block copolymers, even if each block separately shows thermorheologically simple behavior. Block copolymers, in contrast to the polymethacrylates studied by Ferry and co-workers, are not singlephase systems. They form, however, felicitous models for studying materials with multiple transitions because their molecular architecture can be shaped with considerable freedom. We report here on a study of time—temperature superposition in a commercially available triblock copolymer rubber determined in tensile relaxation and creep. 

In an earlier section, we have shown that the viscoelastic behavior of homogeneous block copolymers can be treated by the modified Rouse-Bueche-Zimm model. In addition, the Time-Temperature Superposition Principle has also been found to be valid for these systems. However, if the block copolymer shows microphase separation, these conclusions no longer apply. The basic tenet of the Time-Temperature Superposition Principle is valid only if all of the relaxation mechanisms are affected by temperature in the same manner. Materials obeying this Principle are said to be thermorheologically simple. In other words, relaxation times at one temperature are related to the corresponding relaxation times at a reference temperature by a constant ratio (the shift factor). For... 

Almost always the data from the apparatus above is analyzed by using the time-temperature superposition principle to form a master curve over a wide frequency range at a selected reference temperature. The basis for this procedure is that for thermorheologically simple materials the effect of a change in temperature on... 

However, for thermorheologically simple materials, that is, for those materials for which the time-temperature superposition principle holds, the mechanical properties data can be shifted parallel to the time or frequency axis. This fact suggests an additional hypothesis that can be very useful in solving some specific thermoviscoelastic problems. According to this hypothesis, the net effect of temperature in the response must be equivalent to a variation in the rates of creep or relaxation of the material. Thus for T > Tq the process occurs at a higher rate than at Tq. 

The most common means to extend the frequency scale is to invoke time-temperature superpositioning (Ferry, 1980). If all motions of a polymer contributing to a particular viscoelastic response are affected the same by temperature, then changes in temperature only alter the overall time scale such a material is thermorheologically simple. Thermorheological simplicity means conformance to the time-temperature superposition principle, whereby lower and higher strain rate data can be obtained from measurements at higher and lower temperatures, respectively. 

If the modulus data of a material satisfy Equation (3.27), this material is referred to as thermorheologically simple and obeys the (viscoelastic) time-temperature superposition. 

The combining of time and temperature dependence in the manner described above is referred to as the time-temperature superposition principle. Materials which have this property are sometimes referred to as thermorheologically simple materials. 

Often the assumption is made that a material is thermorheologically simple, meaning all mechanisms contributing to the response have the same temperature dependence. In this situation, temperature only changes the relrixation time, not the shape of the relaxation function. Accordingly, the principle of time-temperature superpositioning can be applied. The measured quantities are shifted... 

---