Thermomechanical

The printing of newspapers is conducted at very high speeds, often reaching 3000 feet per miaute. AH three printing processes utilize similar quaHty newsptint which, essentiaHy, is made of groundwood or thermomechanical pulp. Presses are fed a continuous web of newsptint that unwiads from a feed roUer. Inks dry by absorption of Hquid iato the porosity of the substrate. Some evaporation of water ia a flexo pubHcation ink can accelerate the dryiag process. 

Metallurgy. The strong affinity for oxygen and sulfur makes the rare-earth metals useflil in metallurgy (qv). Mischmetal acts as a trap for these Group 16 (VIA) elements, which are usually detrimental to the properties of steel (qv) or cast iron (qv). Resistance to high temperature oxidation and thermomechanical properties of several metals and alloys are thus significantly improved by the addition of small amounts of mischmetal or its siUcide (16,17). 

Because of constitutional complexity, the exact chemistries of nickel-base superalloys must be controlled carehiUy in order to avoid the precipitation of deleterious topologically close-packed (TCP) phases and extraneous carbides after long-term high temperature exposure. Heat-treatment schedules and thermomechanical treatments in the case of wrought alloys also are important to provide optimum strength and performance. 

Alloy selection depends on several factors, including electrical properties, alloy melting range, wetting characteristics, resistance to oxidation, mechanical and thermomechanical properties, formation of intermetaUics, and ionic migration characteristics (26). These properties determine whether a particular solder joint can meet the mechanical, thermal, chemical, and electrical demands placed on it. 

The TMP process is similar to the RMP process except that after chip washing, a steaming vessel is inserted to achieve the thermoplasticization of the lignin in the wood. The production of thermomechanical pulps increased dramatically after the introduction of this method in the early 1970s. Because these pulps can be substituted for conventional groundwood pulps in newsprint blends to give a stronger paper, lower quantities of the more expensive, lower yield chemical pulps are required. 

R. Marton, A. Brown, and S. Granzow, "Oxygen Pulpiag of Thermomechanical Fiber," 1974 Non-Sulfur Pulping Symposium, Oct. 16—18, Madison, Wis., TAPPI Press, Adanta, Ga. 

Fig. 39. Schematic of the TA Instmments model 2940 thermomechanical analyzer. LVDT = linear variable differential transducer.

Production of Hydrocarbons from Turpentine. In 1993, U.S. production of cmde turpentine was over 128 million liters at an average price of 0.21 /kg and includes cmde sulfate turpentine and turpentine from thermomechanical processes (5). In the same year, over 5.9 million Hters of gum, wood, or sulfate turpentine was imported into the United States, with the majority coming from Canada exports from the United States amounted to 6.16 million liters. 

The dynamic mechanical properties of VDC—VC copolymers have been studied in detail. The incorporation of VC units in the polymer results in a drop in dynamic modulus because of the reduction in crystallinity. However, the glass-transition temperature is raised therefore, the softening effect observed at room temperature is accompanied by increased brittleness at lower temperatures. These copolymers are normally plasticized in order to avoid this. Small amounts of plasticizer (2—10 wt %) depress T significantly without loss of strength at room temperature. At higher levels of VC, the T of the copolymer is above room temperature and the modulus rises again. A minimum in modulus or maximum in softness is usually observed in copolymers in which T is above room temperature. A thermomechanical analysis of VDC—AN (acrylonitrile) and VDC—MMA (methyl methacrylate) copolymer systems shows a minimum in softening point at 79.4 and 68.1 mol % VDC, respectively (86). 

---