Testing planning for

Fig. 4.13. Sequential test plan for direct characteristic comparison... 

PNGV Test Plan For Advanced Technology Development Gen 2 Lithium Ion Cells, EHV-TP-121, Revision 6, October 5, 2001. 

Attend a review of the energetics hydrolysis testing planned for Holston Army Ammunition Plant. Tour facility and observe operations. Holston is a major site for hydrolysis testing of many different types of energetic materials. 

Because there is only one chance to test most physical evidence, it is essential to achieve consensus with interested parties prior to testing. A description of test plans for physical evidence is located in Chapter 8. 

Caterpillar Treetor IL Test planned for turner 1991 Spreader etoker Dollar naklng process stem Reference 1... 

Validation test planning for a database application has the same two principal foundation blocks as for any other type of application the traceability matrix and a risk assessment process. The... 

One potential solution to dealing with extremely deteriorated or shock-sensitive CWM has been investigated by the NSCMP the ballistic tent-and-foam system. According to the testing plan for the ballistic tent-and-foam system,... 

Durability >1000 h 4000 h Testing beyond 1000 hours not conducted expanded durability testing planned for FY 2003. 

Established testing plans for two additional reformer systems. 

Dahlstrom, L-O. 199S. Test Plan for the Prototype Repository. NCC Teknik, SKB, Sweden. Borgesson, L. 2001.Compilation of laboratory data for buffer and backfill materials in the Prototype Repository. Aspo Hard Rock... 

Finding (Pueblo) PH-3. The Parsons/Honeywell WHEAT munitions disassembly machine and the projectile rotary washout machine have not been tested to demonstrate reliable removal of solidified agent to levels sufficiently low for treatment in the metal parts treaters. Testing planned for 2001 may provide data to verify that these machines will be reliable enough to achieve target throughput rates. 

A 2 factorial design is the simplest complete test plan for investigating the influence of n variables on the test result. 

Japan s first generation of electricity an FBR in August 1995 and the electric power was raised gradually for a program of power buildup tests to be carried out the rated power test planned for June 1996. It was in the course of this program that the tip of a thermocouple well tube in the secondaiy circuit (loop C) broke away causing a sodium leak on 8th December 1995. 

Compliance test procedures for steady-state availability Reliability of systems, equipment and components. Guide to reliability testing. Compliance test plans for success ratio... 

Table 2.6 Test plan for field exposed panels...

Table 4.10 Test plan for rust simulation on polished WS...

Test plans for the monitoring were specific to the individual sites and included details for the assembly, exposure, disassembly and evaluation of the coupons. As a minimum evaluation, each site was asked to weigh, clean and photograph each coupon before exposure, and each assembled coupon rack before and after exposure. Detailed metallurgical evaluation of any corrosion was suggested where possible. 

When all components of a preparation process are qualified and validated separately, the largest part of the validation process is complete. The prerequisites are described in a protocol and test plans for the final validation are enclosed. In general process validation includes preparation of three consecutive batches with extended sampling. Acceptance criteria typically include no OOS, no OOT and critical IPC within specified limits. Samples may be collected fi om critical control points during the manufacmre. However, when unit operations have been validated, often only samples of the finished product (after packaging and labelling) are tested. A conclusion about the preparation process as a whole is reported in a Validation report, which has to be approved by the heads of Production, QC and Q A and afterwards will be a base for change control in relation to the process. 

Table 1. Test plan for ISO 10123 pin-collar specimens, tested with clearance fits...

Table 2. Test plan for shaft-hub specimens, tested with interference,...

Table 4. Mechanical Testing Plan for Mechanical Characterization of Composite for Aeronautical Applications...

Conitz, C. C. and Cole, C. M. (1993) Abbreviated Test Plan for Chemical Wei Kms Convention (CWC) Requirements and Assurance Test and Evaluation Non-Destructive Evaluation Systems (RATE-I E), Dugway Proving Ground Report DPG-TP-93-343... 

Optimize maintenance and testing planning for repair and logistics management... 

Test Plan for the Chloronitrobenzene Category. Available at http //www.epa.gov/ hpv/pubs/summaries/chlmbnz/cl4392tc.htm (accessed May 30,2014). 

Table 9 Ruggedness Testing Plan for Sample Preparation (lypc-Bl)... 

The second set of tests is an expanded set of qualification tests that focuses on all key properties that are commonly evaluated for laminates. However, the final decision about a quaUfi-cation test plan for a new laminate should always be driven by product-level requirements, which means that additional laminate tests as well as board-level tests may need to be added to the set of tests described in the following section. 

---