Styrene nitroxide-mediated

Most of the LFRP research ia the 1990s is focused on the use of nitroxides as the stable free radical. The main problems associated with nitroxide-mediated styrene polymerizations are slow polymerization rate and the iaability to make high molecular weight narrow-polydispersity PS. This iaability is likely to be the result of side reactions of the living end lea ding to termination rather than propagation (183). The polymerization rate can be accelerated by the addition of acids to the process (184). The mechanism of the accelerative effect of the acid is not certain. 

The identification of both phenylethyl and 1-phenyl-1,2,3,4-lelrahydronaphthalenyl end groups in polymerizations of styrene retarded by FeCl3/DMP provides the most compelling evidence for the Mayo mechanism.316 The 1-phenyl-1.2,3,4-tetrahydronaphthalenvl end group is also seen amongst other products in the TEMPO mediated polymerization of styrene,317318 However, the mechanism of formation of radicals 96 in this case involves reaction of the nitroxide with the Diels-AIder dimer (Scheme 3.63). The mechanism of nitroxide mediated polymerization is discussed further in Section 9.3.6. 

For SCVP of styrenic inimers, the mechanism includes cationic (14 [18], 19 [29]), atom transfer radical (15 [22, 27]), nitroxide-mediated radical (16 [21]), anionic (20 [19]), photo-initiated radical (17 [2], 18 [52-55]), and ruthenium-catalyzed coordinative (21 [56]) polymerization systems. Another example in-... 

Scheme 3 Schematic representation of the nitroxide mediated polymerization (NMP) of styrene (St)...

Apart from ATRP, the concept of dual initiation was also applied to other (controlled) polymerization techniques. Nitroxide-mediated living free radical polymerization (LFRP) is one example reported by van As et al. and has the advantage that no further metal catalyst is required [43], Employing initiator NMP-1, a PCL macroinitiator was obtained and subsequent polymerization of styrene produced a block copolymer (Scheme 4). With this system, it was for the first time possible to successfully conduct a one-pot chemoenzymatic cascade polymerization from a mixture containing NMP-1, CL, and styrene. Since the activation temperature of NMP is around 100 °C, no radical polymerization will occur at the reaction temperature of the enzymatic ROP. The two reactions could thus be thermally separated by first carrying out the enzymatic polymerization at low temperature and then raising the temperature to around 100 °C to initiate the NMP. Moreover, it was shown that this approach is compatible with the stereoselective polymerization of 4-MeCL for the synthesis of chiral block copolymers. 

Homopolymer PS and block copolymer poly(tert-butyl acrylate)-b-styrene, prepared by nitroxide-mediated living free-radical polymerization, were utilized for the functionalization of shortened SWCNTs through a radical coupling reaction (Scheme 1.33) [194]. 

Spiro-ketal nitroxides have been prepared that are effective as regulators in nitroxide mediated polymerizations. These agents have high hydrocarbon and monomer solubility over existing nitroxides, particularly in styrene, and are also effective as regulators in vinyl acetate and acetonitrile polymerizations. 

Nitroxide mediated polymerization using 1- and 2-nitroso-naphthol were used by Ma [4] to regulate the free radical polymerization of styrene. 

The controlled emulsion polymerization of styrene using nitroxide-mediated polymerization (NMP), reversible addition-fragmentation transfer polymerization (RAFT), stable free radical polymerization (SFR), and atom transfer radical polymerization (ATRP) methods is described. The chain transfer agent associated with each process was phenyl-t-butylnitrone, nitric oxide, dibenzyl trithiocarbonate, 1,1-diphenylethylene, and ethyl 2-bromo-isobutyrate, respectively. Polydispersities between 1.17 and 1.80 were observed. 

Since the nitroxide and the carbon-centered radical diffuse away from each other, termination by combination or disproportionation of two carbon-centered radicals cannot be excluded. This will lead to the formation of dead polymer chains and an excess of free nitroxide. The build-up of free nitroxide is referred to as the Persistent Radical Effect [207] and slows down the polymerization, since it will favor trapping (radical-radical coupling) over propagation. Besides termination, other side reactions play an important role in nitroxide-mediated CRP. One of the important side reactions is the decomposition of dormant chains [208], yielding polymer chains with an unsaturated end-group and a hydroxyamine, TH (Scheme 3, reaction 6). Another side reaction is thermal self-initiation [209], which is observed in styrene polymerizations at high temperatures. Here two styrene monomers can form a dimer, which, after reaction with another styrene monomer, results in the formation of two radicals (Scheme 3, reaction 7). This additional radical flux can compensate for the loss of radicals due to irreversible termination and allows the poly-... 

Preparation of Styrene Block Copolymers Using Nitroxide Mediated Polymerization... 

Nitroxide mediated radical polymerization (NMRP) was pioneered by Riz-zardo and Solomon in the mid-1980s [1]. Their work went unnoticed for almost a decade until Georges et al. reported the preparation of narrow polydispersity (PD) (<1.2) polystyrene using NMRP [2]. This report initiated an explosion of research aimed at both understanding the mechanism of NMRP and also utilizing it to prepare block copolymers. This chapter describes the application and limitations of NMRP for making styrene-containing block copolymers. 

Since polystyrene is one of the oldest commercial polymers with over 9 million tonnes/yr of sales, there have been thousands of patents issued covering all aspects of its manufacture and property enhancement. The styrene monomer readily polymerizes to polystyrene either thermally or with free-radical initiators (see Chapter 6 on free-radical polymerization and Chapter 8 on nitroxide-mediated polymerization). Commercial processes for the manufacture of polystyrene are described in Chapter 3 while process modelling and optimization of styrene polymerization is examined in Chapter 5. Styrene also can be polymerized via anionic and Ziegler-Natta chemistries using organometallic initiators. Using free radical and anionic polymerization chemistries, the... 

The radical nature of nitroxide-mediated processes also allows novel types of block copolymers to be prepared in which copolymers, not homopolymer, are employed as one of the blocks. One of the simplest examples incorporate random copolymers124 and the novelty of these structures is based on the inability to prepare random copolymers by living anionic or cationic procedures. This is in direct contrast to the facile synthesis of well-defined random copolymers by nitroxide-mediated systems. While similar in concept, random block copolymers are more like traditional block copolymers than random copolymers in that there are two discrete blocks, the main difference being one or more of these blocks is composed of a random copolymer segment. For example, homopolystyrene starting blocks can be used to initiate the copolymerization of styrene and 4-vi-nylpyridine to give a block copolymer consisting of a polystyrene block and a random copolymer of styrene and 4-vinylpyridine as the second block.166... 

The covalent bonds for dormant species include C—C (eq l),1617 C—S (eqs 2 and 9),131418 C—Se (eq 3),19 C—O (eqs 4 and 5),20 25 C—halogen (eqs 6 and 8),26 28 and C—metal (eq 7),29 all of which can reversibly and homolytically be activated into the growing radical species by physical stimuli such as heat or light or by chemical stimuli such as a metal catalyst or another radical species. Although the controllability, applicability, and reaction conditions depend on which systems are employed, a wide variety of vinyl monomers such as styrenes, methacrylates, acrylates, dienes, and vinyl acetate can be polymerized in a controlled fashion with the use of these or similar systems. Among these, nitroxide-mediated (eq 4)20 24 and metal-catalyzed27 28 systems... 

For styrene-based random copolymers, functional groups can be introduced into the polymer chains via copolymerization with functional styrene derivatives, because the electronic effects of the substituents are small in the metal-catalyzed polymerizations in comparison to the ionic counterparts. Random copolymer R-6 is of this category, synthesized from styrene and />acetoxystyrene.372 It can be transformed into styrene// -vinylphenol copolymers by hydrolysis.380 The benzyl acetate and the benzyl ether groups randomly distributed in R-7 and R-8 were transformed into benzyl bromide, which can initiate the controlled radical polymerizations of styrene in the presence of copper catalysts to give graft copolymers.209 Epoxy groups can be introduced, as in R-9, by the copper-catalyzed copolymerizations without loss of epoxy functions, while the nitroxide-mediated systems suffer from side reactions due to the high-temperature reaction.317... 

The metal-catalyzed copolymerization from carbon-halogen bonds in the main chain can be employed widely for graft polymer synthesis. A combination of nitroxide-mediated and copper-catalyzed living radical polymerizations, for example, gives graft copolymers G-6, where the main chain is prepared by the former.432 The chlorobenzyl unit in the copolymer is not active during the polymerization but, upon copper catalysis, it can initiate living radical polymerizations of styrene and methacrylates. 

While possessing many of the key advantages of controlled/ living polymerization methods, nitroxide-mediated free-radical polymerizations do exhibit several limitations. The range of monomers that have been polymerized using nitroxide-mediated techniques include styrenics. acrylamides and (meth)acrylates but these have predominantly been reported in bulk polymerizations (i.e. without solvent) and are conducted at elevated temperature for long time periods. In addition, synthesis of the unimolecular initiator can prove troublesome (dependent upon the type required) and often requires extensive purification in order to attain sufficient purity levels to allow molecular weight control. 

Scheme 1.33. Nitroxide-mediated living radical polymerization of styrene using TEMPO. After Hawker et al. (2001).

The following sections detail the literature reports pertaining to the synthesis of block copolymers using nitroxide-mediated polymerization techniques. The sections are organized according to monomer type and generally follow the historical development of the particular subsection. Most literature on nitroxide mediated preparation of block copolymers is found for the styrene-based monomers, and is summarized first. This is followed by acrylates and dienes, as they were the next monomers to be studied. These sections are followed by more recent work with vinyl pyridine, acrylamides, and maleic anhydride. The final section deals with methacrylates. This is presented last to stress the importance of developing new nitroxides that can successfully be used for the homopolymerization of methacrylate-based monomers. 

---