Aprotic polar solvent

Polar protic solvents Polar aprotic solvents Non-polar solvents ... 

Solvent Effects on the Rate of Substitution by the S 2 Mechanism Polar solvents are required m typical bimolecular substitutions because ionic substances such as the sodium and potassium salts cited earlier m Table 8 1 are not sufficiently soluble m nonpolar solvents to give a high enough concentration of the nucleophile to allow the reaction to occur at a rapid rate Other than the requirement that the solvent be polar enough to dis solve ionic compounds however the effect of solvent polarity on the rate of 8 2 reactions IS small What is most important is whether or not the polar solvent is protic or aprotic Water (HOH) alcohols (ROH) and carboxylic acids (RCO2H) are classified as polar protic solvents they all have OH groups that allow them to form hydrogen bonds... 

Rate increases with increasing po larity of solvent as measured by its dielectric constant e (Section 8 12) Polar aprotic solvents give fastest rates of substitution solvation of Nu IS minimal and nucleophilicity IS greatest (Section 8 12)... 

HCN(CH3)2 DMF IS a polar aprotic solvent (Section 8 12) and an excellent medium for Sm2 reactions... 

This IS an example of an Sn2 reaction in a polar aprotic solvent... 

Synthesis and Properties. Several methods have been suggested to synthesize polyimides. The predominant one involves a two-step condensation reaction between aromatic diamines and aromatic dianhydrides in polar aprotic solvents (2,3). In the first step, a soluble, linear poly(amic acid) results, which in the second step undergoes cyclodehydration, leading to an insoluble and infusible PL Overall yields are generally only 70—80%. 

New heat-resistant polymers containing -iiitrophenyl-substituted quinoxaline units and imide rings as well as flexible amide groups have been synthesi2ed by polycondensation reaction of a dianainoquinoxaline derivative with diacid dichlorides (80). These polymers are easily soluble in polar aprotic solvents with inherent viscosities in the range of 0.3—0.9 dL/g in NMP at 20°C. AH polymers begin to decompose above 370°C. 

Aromatic Radical Anions. Many aromatic hydrocarbons react with alkaU metals in polar aprotic solvents to form stable solutions of the corresponding radical anions as shown in equation 8 (3,20). These solutions can be analyzed by uv-visible spectroscopy and stored for further use. The unpaired electron is added to the lowest unoccupied molecular orbital of the aromatic hydrocarbon and a... 

Aluminum chloride dissolves readily in chlorinated solvents such as chloroform, methylene chloride, and carbon tetrachloride. In polar aprotic solvents, such as acetonitrile, ethyl ether, anisole, nitromethane, and nitrobenzene, it dissolves forming a complex with the solvent. The catalytic activity of aluminum chloride is moderated by these complexes. Anhydrous aluminum chloride reacts vigorously with most protic solvents, such as water and alcohols. The ability to catalyze alkylation reactions is lost by complexing aluminum chloride with these protic solvents. However, small amounts of these "procatalysts" can promote the formation of catalyticaHy active aluminum chloride complexes. 

Sodium and magnesium do not react with tetrachlorosilane at room temperature, but do so at elevated temperatures and ia the presence of polar aprotic solvents at moderately elevated temperatures. The Wurtz-Fittig coupling of organosilanes to form disilanes (168) and polysdanes (169) is usually accomphshed usiag molten sodium ia toluene or xylene. 

The polarity of the polymer is important only ia mixtures having specific polar aprotic solvents. Many solvents of this general class solvate PVDC strongly enough to depress the melting temperature by more than 100°C. SolubiUty is normally correlated with cohesive energy densities or solubiUty parameters. For PVDC, a value of 20 0.6 (J/cm (10 0.3 (cal/cm ) has been estimated from solubiUty studies ia nonpolar solvents. The value... 

Poly(vinyhdene chloride) also dissolves readily in certain solvent mixtures (82). One component must be a sulfoxide or A/,Al-diaIk5lamide. Effective cosolvents are less polar and have cycHc stmctures. They include aUphatic and aromatic hydrocarbons, ethers, sulfides, and ketones. Acidic or hydrogen-bonding solvents have an opposite effect, rendering the polar aprotic component less effective. Both hydrocarbons and strong hydrogen-bonding solvents are nonsolvents for PVDC. 

The degradation of VDC polymers in nonpolar solvents is comparable to degradation in the soHd state (101,125,129,130). However, these polymers are unstable in many polar solvents (131). The rate of dehydrochlorination increases markedly with solvent polarity. In strongly polar aprotic solvents, eg, hexamethylphosphoramide, dehydrochlorination proceeds readily (129,132). This reaction is cleady unlike thermal degradation and may well involve the generation of ionic species as intermediates. 

Traditionahy, the reactions to be considered here are performed in homogenous medium, either in hydroxyUc solvents or in polar aprotic solvents. In comparison, PTC has the foUowing advantages no need for expensive aprotic solvents simpler work-up shorter reaction time and or lower reaction temperature use of aqueous alkaU hydroxides instead of other expensive bases. 

It is prepared from the polycondensation of the disodium salt of bisphenol A and 4,4-dichlorodiphenyl sulfone in a polar aprotic solvent such as dimethyl sulfoxide (26). 

Instead of Hquid ammonia, aqueous ammonia is also used together with a polar aprotic solvent such as formamide (48). It is also prepared by sulfonating... 

The realization that die nucleophilicity of anions is strongly enhanced in polar aprotic solvents has led to important improvements of several types of synthetic processes that involve nucleophilic substitutions or additions. 

Neopentyl (2,2-dimethylpropyl) systems are resistant to nucleo diilic substitution reactions. They are primary and do not form caibocation intermediates, but the /-butyl substituent efiTectively hinders back-side attack. The rate of reaction of neopent>i bromide with iodide ion is 470 times slower than that of n-butyl bromide. Usually, tiie ner rentyl system reacts with rearrangement to the /-pentyl system, aldiough use of good nucleophiles in polar aprotic solvents permits direct displacement to occur. Entry 2 shows that such a reaction with azide ion as the nucleophile proceeds with complete inversion of configuration. The primary beiuyl system in entry 3 exhibits high, but not complete, inversiotL This is attributed to racemization of the reactant by ionization and internal return. 

Sodium acetate reacts with /p-nitrophenyl benzoates to give mixed anhydrides if the reaction is conducted in a polar aprotic solvent in the presence of a crown ether. The reaction is strongly accelerated by quartemary nitrogen groups substituted at the orthc position. Explain the basis for the enhanced reactivity of these compounds. 

---