Solid-phase amination

Two groups [127, 128] have reported results on the solid-phase amination of aryl halides using both P(o-C6H4Me)3 and chelating ligands. It has been shown that Stille and Suzuki reactions are reliable, high-yielding processes for substrates loaded on solid supports [129]. Thus, supported aryl halides can now be used to form new C C and C-N bonds, and presumably C S, CP, and CO bonds as well. 

In the solid phase, amine hydrohalides containing have an absorption... 

Then N-Boc-O-benzylserine is coupled to the free amino group with DCC. This concludes one cycle (N° -deprotection, neutralization, coupling) in solid-phase synthesis. All three steps can be driven to very high total yields (< 99.5%) since excesses of Boc-amino acids and DCC (about fourfold) in CHjClj can be used and since side-reactions which lead to soluble products do not lower the yield of condensation product. One side-reaction in DCC-promoted condensations leads to N-acylated ureas. These products will remain in solution and not reaa with the polymer-bound amine. At the end of the reaction time, the polymer is filtered off and washed. The times consumed for 99% completion of condensation vary from 5 min for small amino acids to several hours for a bulky amino acid, e.g. Boc-Ile, with other bulky amino acids on a resin. A new cycle can begin without any workup problems (R.B. Merrifield, 1969 B.W. Erickson, 1976 M. Bodanszky, 1976). 

In recent years the solid-phase hydrosilylation reaction was successfully employed for synthesis of hydrolytically stable surface chemical compounds with Si-C bonds. Of special interest is application of this method for attachment of functional olefins, in particular of acrolein and some chiral ligands. Such matrices can be used for subsequent immobilization of a wide range of amine-containing organic reagents and in chiral chromatography. 

Rapid purification Stir over CaH2 (5% w/v) overnight, filter, then distil at 20mmHg. Store the distd DMF over 3A or 4A molecular sieves. For solid phase synthesis, the DMF used must be of high quality and free from amines. 

The Zincke reaction has also been adapted for the solid phase. Dupas et al. prepared NADH-model precursors 58, immobilized on silica, by reaction of bound amino functions 57 with Zincke salt 8 (Scheme 8.4.19) for subsequent reduction to the 1,4-dihydropyridines with sodium dithionite. Earlier, Ise and co-workers utilized the Zincke reaction to prepare catalytic polyelectrolytes, starting from poly(4-vinylpyridine). Formation of Zincke salts at pyridine positions within the polymer was achieved by reaction with 2,4-dinitrochlorobenzene, and these sites were then functionalized with various amines. The resulting polymers showed catalytic activity in ester hydrolysis. ... 

Peptide synthesis requires the use of selective protecting groups. An N-protected amino acid with a free carboxyl group is coupled to an O-protected amino acid with a free amino group in the presence of dicydohexvlcarbodi-imide (DCC). Amide formation occurs, the protecting groups are removed, and the sequence is repeated. Amines are usually protected as their teit-butoxy-carbonyl (Boc) derivatives, and acids are protected as esters. This synthetic sequence is often carried out by the Merrifield solid-phase method, in which the peptide is esterified to an insoluble polymeric support. 

Hlasta and Deng have developed a two-step solid-phase method for the decoration of azoles at C-2 [188]. First, imidazole was loaded onto a polystyrene-bound carbamyl chloride via a benzaldehyde bridge (Fig. 40). The 2-substi-tuted imidazole was efficiently cleaved in good yields in the presence of various nucleophiles (i.e., water, alcohols, and amines), trifluoroacetic acid, and boron trifluoride under microwave irradiation in a closed vessel at 120 °C for 5 min. 

To perform Diels-Alder reactions on solid phase, the 2(lH)-pyrazinone scaffold is linked to a suitable support via its amide nitrogen atom. While N-l-substituted pyrazinones are readily accessible by the choice of an appropriate amine, it is not possible to prepare N-l-unsubstituted pyrazinones using the general strategy as previously outlined in the introduction. How-... 

Unsymmetrical as well as symmetrical anhydrides are often prepared by the treatment of an acyl halide with a carboxylic acid salt. The compound C0CI2 has been used as a catalyst. If a metallic salt is used, Na , K , or Ag are the most common cations, but more often pyridine or another tertiary amine is added to the free acid and the salt thus formed is treated with the acyl halide. Mixed formic anhydrides are prepared from sodium formate and an aryl halide, by use of a solid-phase copolymer of pyridine-l-oxide. Symmetrical anhydrides can be prepared by reaction of the acyl halide with aqueous NaOH or NaHCOa under phase-transfer conditions, or with sodium bicarbonate with ultrasound. 

The second step introduces the side chain group by nucleophilic displacement of the bromide (as a resin-bound a-bromoacetamide) with an excess of primary amine. Because there is such diversity in reactivity among candidate amine submonomers, high concentrations of the amine are typically used ( l-2 M) in a polar aprotic solvent (e.g. DMSO, NMP or DMF). This 8 2 reaction is really a mono-alkylation of a primary amine, a reaction that is typically complicated by over-alkylation when amines are alkylated with halides in solution. However, since the reactive bromoacetamide is immobilized to the solid support, any over-alkyla-tion side-products would be the result of a cross-reaction with another immobilized oligomer (slow) in preference to reaction with an amine in solution at high concentration (fast). Thus, in the sub-monomer method, the solid phase serves not only to enable a rapid reaction work-up, but also to isolate reactive sites from... 

A variety of cleavage conditions have been reported for the release of amines from a solid support. Triazene linker 52 prepared from Merrifield resin in three steps was used for the solid-phase synthesis of aliphatic amines (Scheme 22) [61]. The triazenes were stable to basic conditions and the amino products were released in high yields upon treatment with mild acids. Alternatively, base labile linker 53 synthesized from a-bromo-p-toluic acid in two steps was used to anchor amino functions (Scheme 23) [62]. Cleavage was accomplished by oxidation of the thioether to the sulfone with m-chloroperbenzoic acid followed by 13-elimination with a 10% solution of NH4OH in 2,2,2-trifluoroethanol. A linker based on l-(4,4 -dimethyl-2,6-dioxocyclohexylidene)ethyl (Dde) primary amine protecting group was developed for attaching amino functions (Scheme 24) [65]. Linker 54 was stable to both acidic and basic conditions and the final products were cleaved from the resin by treatment with hydrazine or transamination with ra-propylamine. 

A-Protected amines were assembled on solid-phase via sulfonamide-based handle 58 (Scheme 27) [67]. Tertiary sulfonamides were generated upon reaction with allylic, benzylic and primary alcohols under Mitsu-nobu conditions. Secondary amines were released from the support using mild nucleophilic conditions such as treatment with thiophenol and potassium carbonate. 

A versatile approach for the solid-phase synthesis of aminopyr-idazines used the anchoring of 3,6-dichloropyridazine to resin-bound thiophenol 59 (Scheme 28) [68]. Treatment with nucleophilic amines released the aminopyridazine products from the solid support without further oxidation. 

---