Small Particle Catalyst

A major feature of this process is using the horizontal converter and small-particle catalyst, so that the gas flows the path shortly, its linear speed is small, the pressure drop decreases in the catalyst bed, and consequently the recycle-compress power can be saved the catalytic activity can be improved by 12%-25%. Thus the catalyst volume and the equipment size decreases, the net value of the ammonia increases, the amount of the recycle gas declines there is homogeneous distribution of the gas-flow so that gets the higher synthetic ratio, and the energy consumption is significantly reduced. 

Prepare a saturated solution of sodium sulphide, preferably from the fused technical sodium polysulphide, and saturate it with sulphur the sulphur content should approximate to that of sodium tetrasulphide. To 50 ml. of the saturated sodium tetrasulphide solution contained in a 500 ml. round-bottomed flask provided with a reflux condenser, add 12 -5 ml. of ethylene dichloride, followed by 1 g. of magnesium oxide to act as catalyst. Heat the mixture until the ethylene dichloride commences to reflux and remove the flame. An exothermic reaction sets in and small particles of Thiokol are formed at the interface between the tetrasulphide solution and the ethylene chloride these float to the surface, agglomerate, and then sink to the bottom of the flask. Decant the hquid, and wash the sohd several times with water. Remove the Thiokol with forceps or tongs and test its rubber-like properties (stretching, etc.). 

The available surface area of the catalyst gready affects the rate of a hydrogenation reaction. The surface area is dependent on both the amount of catalyst used and the surface characteristics of the catalyst. Generally, a large surface area is desired to minimize the amount of catalyst needed. This can be accomphshed by using either a catalyst with a small particle size or one with a porous surface. Catalysts with a small particle size, however, can be difficult to recover from the material being reduced. Therefore, larger particle size catalyst with a porous surface is often preferred. A common example of such a catalyst is Raney nickel. 

These reactors for hquids and liquids plus gases employ small particles in the range of 0.05 to 1.0 mm (0.0020 to 0.039 in), the minimum size hmited by filterability. Small diameters are used to provide as large an interface as possible since the internal surface of porous pellets is poorly accessible to the hquid phase. Solids concentrations up to 10 percent by volume can be handled. In hydrogenation of oils with Ni catalyst, however, the sohds content is about 0.5 percent, and in the manufacture of hydroxylamine phosphate with Pd-C it is 0.05 percent. Fischer-Tropsch slurry reac tors have been tested with concentrations of 10 to 950 g catalyst/L (0.624 to 59.3 IbiTi/fF) (Satterfield and Huff, Chem. Eng. Sci., 35, 195 [1980]). 

This reaction is carried out in tall fluidized beds of high L/dt ratio. Pressures up to 200 kPa are used at temperatures around 300°C. The copper catalyst is deposited onto the surface of the silicon metal particles. The product is a vapor-phase material and the particulate silicon is gradually consumed. As the particle diameter decreases the minimum fluidization velocity decreases also. While the linear velocity decreases, the mass velocity of the fluid increases with conversion. Therefore, the leftover small particles with the copper catalyst and some debris leave the reactor at the top exit. 

Thus, two factors may be pointed out that determine the possibility of obtaining high yields of crystalline polyethylene on a solid catalyst with no diffusional restriction (1) the splitting up of the catalyst into small particles (< 1000 A), possible when using supports with low resistance to breaking (2) the formation of polymer grains with polydispersed porosity. 

When the mass transfer resistances are eliminated, the various gas-phase concentrations become equal a/(/, r, z) = j(r, z) = a(r, z). The very small particle size means that heat transfer resistances are minimized so that the catalyst particles are isothermal. The recycle reactor of Figure 4.2 is an excellent means for measuring the intrinsic kinetics of a finely ground catalyst. At high recycle rates, the system behaves as a CSTR. It is sometimes called a gradientless reactor since there are no composition and temperature gradients in the catalyst bed or in a catalyst particle. 

The value for is conservatively interpreted as the particle diameter. This is a perfectly feasible size for use in a laboratory reactor. Due to pressure-drop limitations, it is too small for a full-scale packed bed. However, even smaller catalyst particles, dp 50 yum, are used in fluidized-bed reactors. For such small particles we can assume rj=l, even for the 3-nm pore diameters found in some cracking catalysts. 

In Chapter 1 we emphasized that the properties of a heterogeneous catalyst surface are determined by its composition and structure on the atomic scale. Hence, from a fundamental point of view, the ultimate goal of catalyst characterization should be to examine the surface atom by atom under the reaction conditions under which the catalyst operates, i.e. in situ. However, a catalyst often consists of small particles of metal, oxide, or sulfide on a support material. Chemical promoters may have been added to the catalyst to optimize its activity and/or selectivity, and structural promoters may have been incorporated to improve the mechanical properties and stabilize the particles against sintering. As a result, a heterogeneous catalyst can be quite complex. Moreover, the state of the catalytic surface generally depends on the conditions under which it is used. 

Figure 4.1. Supported catalyst, consisting of small particles on a high surface area carrier such as silica or alumina, along with two simplified model systems, which in general offer much better opportunities for characterization at the molecular level.

The example is typical for many applications of Mossbauer spectroscopy in catalysis a catalyst undergoes a certain treatment, then its Mossbauer spectrum is measured in situ at room temperature. Flowever, if the catalyst contains highly dispersed particles, the measurement of spectra at cryogenic temperatures becomes advantageous as the recoil-free fraction of surface atoms increases substantially at temperatures below 300 K. Secondly, spectra of small particles that behave superparamagne-... 

Catalysts can be metals, oxides, sulfides, carbides, nitrides, acids, salts, virtually any type of material. Solid catalysts also come in a multitude of forms and can be loose particles, or small particles on a support. The support can be a porous powder, such as aluminium oxide particles, or a large monolithic structure, such as the ceramics used in the exhaust systems of cars. Clays and zeolites can also be solid catalysts. 

---