Section longitudinal

On testing pro pints, each sample should contain as many whole grains. as possible but, if the grains ate too large, they should be sectioned longitudinally... 

Paraffin blocks are trimmed with a scalpel, a razor blade, or a hot spatula and mounted on wooden or fiber blocks. While being sectioned, longitudinal block edges must be parallel to the knife edge to obtain a ribbon. Paraffin sections of any thickness show compression, which is usually relieved when they are floated on a glass slide and dried. 

Species Tooth type Overall shape and size Shape X-section Longitudinal section Cementum X-section Dentine X-section... 

Ruggenenti P, Gaspari F, Perna A, Remuzzi G. Cross-sectional longitudinal study of spot morning urine protein creatinine ratio, 24-hour urine protein excretion rate, glomerular filtration rate, and end stage renal failure in chronic renal disease in patients without diabetes, BMJ 1998 316 504-9. 

Ruggenenti P, Gaspari F, Pema A, Remuzzi G. Cross-sectional longitudinal study of spot morning urine protein creatinine ratio, 24-hour 56. 

Figure 11 (see color section). Longitudinal H-bond relay comprised of CHQs and water, (a) Tubular polymer structure of a single nanotube obtained with X-ray analysis for the heavy atoms and with ab initio calculations for the H-orientations (top and side views), (b) One of the four pillar frames of short H-bonds represents a 1-D H-bond relay composed of a series of consecutive OH groups [hydroxyl groups (—OH) in CHQs and the OHs in water molecules]. Reproduced by permission of American Chemical Society Ref. [54]. 

Tubular adenosis Tubules sectioned longitudinally and lack lobulocentric distribution Present Present S-1 00-... 

Each day several tomatoes were sectioned longitudinally into... 

During the stretching of tubular films, as discussed in the previous section, longitudinal and transverse stretching are usually carried out simultaneously. This is also possible in flat-film stretching by means of a tenter frame. 

Peripheral trapezoidal structure welded by two box section longitudinal beams and several box or tube section cross beams. 

Figure 111(a) and (b). PAN (polyacrylonitrile) fibers in an anisotropic pyrocarbon matrix, POL. (a) fibers sectioned longitudinally, (b) fibers sectioned transversely. Cavities are dark. 

Use now this equation to describe liquid film flow in conical capillary. Let us pass to spherical coordinate system with the origin coinciding with conical channel s top (fig. 3). It means that instead of longitudinal coordinate z we shall use radial one r. Using (6) we can derive the total flow rate Q, multiplying specific flow rate by the length of cross section ... 

Intersections of butts and seams of fabrication and section welds Throughout hull envelope, longitudinal and transverse bulkheads, inner bottom and hopper bottom The summation of checkpoint lengths (see note 2) examined at intersections is to be L where L is the overall length of the ship in metres... 

This decomposition into a longitudinal and a hansverse part, as will be discussed in Section III, plays a crucial role in going to a diabatic representation in which this singularity is completely removed. In addition, the presence of the first derivative gradient term W l Rx) Vr x (Rx) in Eq. (15), even for a nonsingular Wi i (Rx) (e.g., for avoided intersections), introduces numerical inefficiencies in the solution of that equation. 

The cavity of a laser may resonate in various ways during the process of generation of radiation. The cavity, which we can regard as a rectangular box with a square cross-section, has modes of oscillation, referred to as cavity modes, which are of two types, transverse and axial (or longitudinal). These are, respectively, normal to and along the direction of propagation of the laser radiation. 

It is difficult to determine the cross-sectional area of a fiber. Direct observation and measurement of a cross section under a microscope is the most accurate method (15). This is a destmctive test that does not allow subsequent study of fiber mechanical properties, and is slow and tedious. Also, it does not take into account any variations in the cross-sectional area along the fiber length. Measurement of fiber diameters from microscopic observations of longitudinal views is somewhat easier, but the eUipticity of the cross section in certain fibers can lead to serious errors. 

Fig. 1. Typical longitudinal section of bast fiber showing very long fiber strands composed of many ultimate fibers (see Table 3 for dimensions).

Fig. 8. Longitudinal section of an experimental waste-heat greenhouse in which temperature control in all seasons is provided by evaporation and heat...

Fig. 7. Typical crimp contacts. Insets are cross sections of crimp indentations (a) is longitudinal (b), square (c), double indent (d), 4 indent (e), B crimp ...

FIG. 11-42 Doiihle-pipe-exchanger section An.th longitudinal fins. (Brown Fin-tube Co. )... 

Figure 2.26 As in Fig. 2.25. Longitudinal cross section through tunnel. (Magnification 15x.)...

Two sections of steel condenser tubing experienced considerable metal loss from internal surfaces. An old section contained a perforation the newer section had not failed. A stratified oxide and deposit layer overlaid all internal surfaces (Fig. 5.14). Corrosion was severe along a longitudinal weld seam in the older section (Fig. 5.15). Differential oxygen concentration cells operated beneath the heavy accumulation of corrosion products and deposits. The older tube perforated along a weld seam. 

Figure 6.9S Longitudinal cross section showing a pit tunneling into an incompletely closed weld seam.

---