Screening sintering

Conventional up-draught sinter plant including feed mixing with return sinter, feed conditioning and moisture control, sinter strand, product sinter crushing and screening, sinter storage. 

Characteristics Square Weave Screen Dutch Twill Weave Screen Sintered Powder Metal Fiber... 

The Utah deposit is located in southwestern Utah near Cedar City. The iron ore deposits are of contact metamorphic origin. The cmde ore contains 35 to 65% iron, primarily in the form of magnetite and goethite. Mining is done by the open pit method. The cmde ore is cmshed, screened at —75 mm (—200 mesh size) and shipped as lump ore containing 54% iron. The ore is rescreened at the steel mill to produce lump ore (10—64 mm) for the blast furnace and sinter feed (0—10 mm) for the sinter plant. 

Filtered-Particle Inspection. Solids containing extensive inteiconnected porosity, eg, sintered metallic or fired ceramic bodies formed of particles that ate typically of 0.15-mm (100-mesh) screen size, are not inspectable by normal Hquid penetrant methods. The preferred test medium consists of a suspension of dyed soHd particles, which may be contained in a Hquid vehicle dyed with a different color. Test indications can form wherever suspensions can enter cracks and other discontinuities open to the surface and be absorbed in porous material along interior crack walls. The soHd particles that form test indications ate removed by filtration along the line of the crack at the surface where they form color or fluorescent indications visible under near-ultraviolet light (1,3). 

Another preparation method is a sintering process where phosphate ore, sand, and coal are blended together and ignited on the grates of a sintering machine. Air is pulled through the blend, and the entire mass is allowed to bum. The resulting fused bed of material is then cmshed and screened to the appropriate size distribution, and the undersized material is reprocessed. 

One other method used to size the phosphate ore is disk agglomeration. After preparation, the disk agglomerates are sintered at high temperature in separate process steps, followed by screening to the appropriate size specifications. 

Lower cost and lower weight cylindrical cells have been made using plastic bound or pasted actwe material pressed into a metal screen. Tliese cells suffer slightly in utilization at high rates compared to a sintered-plate cylindrical cell, but they may be adequate for most applications. Tlie effect of temperature and discharge rate on the capacity of sealed nickel-cadmium cells is illustrated in Figure 8 and Table 3. 

An electrostatic precipitator is used to remove more tar from coke oven gas. The tar is then sent to storage. Ammonia liquor is also separated from the tar decanter and sent to wastewater treatment after ammonia recovery. Coke oven gas is further cooled in a final cooler. Naphthalene is removed in a separator on the final cooler. Light oil is then removed from the coke oven gas and is fractionated to recover benzene, toluene, and xylene. Some facilities may include an onsite tar distillation unit. The Claus process is normally used to recover sulfur from coke oven gas. During the coke quenching, handling, and screening operation, coke breeze is produced. The breeze is either reused on site (e.g., in the sinter plant) or sold offsite as a by-product. 

The filter floor and cloth, woven mesh screen or sintered metal plate medium... 

The fused sinter mass is cooled, crushed, screened, and sent to be charged, along with the ore, to the blast furnace. Approximately 2.5 t of raw materials, including water and fuel, are required to... 

Sinter strand Crushing Hot screening Cooling and cold screening — ( blast... 

Emissions from sinter plants are generated from raw material handling, windbox exhaust, sinter discharge (associated sinter crushers and hot screens), and from the cooler and cold screen. The primary source of particulate emissions, mainly irons oxides, magnesium oxide, sulfur oxides, carbonaceous compounds, aliphatic hydrocarbons, and chlorides, are due to the windbox exhaust. Contaminants such as fluorides, ammonia, and arsenic may also be present. At the discharge end,... 

---