Reversible addition-fragmentation copolymers

Synthesis of Block Copolymers by Reversible Addition-Fragmentation Chain Transfer Radical Polymerization, RAFT... 

To make further use of the azo-initiator, tethered diblock copolymers were prepared using reversible addition fragmentation transfer (RAFT) polymerization. Baum and co-workers [51] were able to make PS diblock copolymer brushes with either PMMA or poly(dimethylacrylamide) (PDMA) from a surface immobihzed azo-initiator in the presence of 2-phenylprop-2-yl dithiobenzoate as a chain transfer agent (Scheme 3). The properties of the diblock copolymer brushes produced can be seen in Table 1. The addition of a free initiator, 2,2 -azobisisobutyronitrile (AIBN), was required in order to obtain a controlled polymerization and resulted in the formation of free polymer chains in solution. 

Scheme 3 Synthesis of surface-immobilized diblock copolymer brush (Si/Si02//PS-fc-PDMA) using reverse addition fragmentation transfer polymerization...

Hawker et al. 2001 Hawker and Wooley 2005). Recent developments in living radical polymerization allow the preparation of structurally well-defined block copolymers with low polydispersity. These polymerization methods include atom transfer free radical polymerization (Coessens et al. 2001), nitroxide-mediated polymerization (Hawker et al. 2001), and reversible addition fragmentation chain transfer polymerization (Chiefari et al. 1998). In addition to their ease of use, these approaches are generally more tolerant of various functionalities than anionic polymerization. However, direct polymerization of functional monomers is still problematic because of changes in the polymerization parameters upon monomer modification. As an alternative, functionalities can be incorporated into well-defined polymer backbones after polymerization by coupling a side chain modifier with tethered reactive sites (Shenhar et al. 2004 Carroll et al. 2005 Malkoch et al. 2005). The modification step requires a clean (i.e., free from side products) and quantitative reaction so that each site has the desired chemical structures. Otherwise it affords poor reproducibility of performance between different batches. 

Prepared by bulk polymerization, an MIP for the detection of dicrotophos based on the Eu3+ complex has recently been presented [58]. The authors used reversible addition fragmentation chain transfer (RAFT) polymerization followed by ring closing methathesis (RCM) to obtain the star MIP with arms made out of block copolymer. The star MIP containing Eu3+ exhibited strong fluorescence when excited at 338 nm with a very narrow emission peak (half width -10 nm) at 614 nm. This MIP was sensitive to dicrotophos in the range of 0-200 ppb, but showed saturation above this limit. Cross-reactivity of this MIP was evaluated with respect to structurally similar compounds dichlorvos, diazinon and dimethyl methylphosphonate. In these tests no optical response of the polymer was detected even at concentrations much higher than the initial concentration of dicrotophos (>1000 ppb). 

In 1998, Chiefari et al. [10] attempted to combine the convenience of radical polymerization with the many benefits of living polymerization, e.g. control of the molecular weight and polydispersity and the possibility of synthesizing block copolymers of complex architecture. They used free-radical polymerization reagents of formula (I) to produce a sequence of reversible addition-fragmentation in which the transfer of the S=C (Z) S moiety between active and dormant chains serves to maintain the living character of the polymerization ... 

Living radical polymerizations in miniemulsions have also been conducted by de Brouwer et al. using reversible addition-fragmentation chain transfer (RAFT) and nonionic surfactants [98]. The polydispersity index was usually below 1.2. The living character is further exemplified by its transformation into block copolymers. 

Economically produced block copolymers containing acrylonitrile or methacrylo-nitrile as the principal component have been prepared that are heat resistant, weath-erable, and oil and flame resistant. These materials were prepared using reversible addition-fragmentation chain transfer polymerization. 

Controlled free-radical polymerization (CFRP) has been used successfully to produce block, graft, and other controlled architecture copolymers within the last decade for a variety of free radically polymerizable monomers. The main techniques include reversible addition fragmentation and transfer (RAFT) polymerization, stable free-radical polymerization (SFRP) mediated by nitroxide/alkoxyamine based radicals, atom transfer radical polymerization (ATRP), diphenyl ethylene (DPE) mediated polymerization, and novel precipitation/emulsion polymerization based methods like free-radical retrograde precipitation polymerization (FRRPP). ... 

An alternative approach uses reversible addition-fragmentation chain transfer (RAFT), which has fewer limitations in the selection of monomers (Chong et al, 1999) so that monomers with hydroxyl, t-amino and acid functionality may be polymerized into narrow-polydispersity block copolymers. The RAFT agent is a dithioester of the general formula S=C(Z)S-R, where Z is usually -Ph (phenyl) and R is chosen from a group of alkyl phenyls (e.g. -C(CH3)2Ph). 

Figure 13.3 Overview showing the use of bifunctional initiators for block-copolymer synthesis. Two examples using either reversible addition fragmentation chain transfer polymerization or atom transfer radical polymerization combined with eROP are shown.

The bifunctional initiator approach using reversible addition fragmentation chain-transfer polymerization (RAFT) as the free-radical controlling mechanism was soon to follow and block copolymers of styrene and caprolactone ensued [58]. In this case, a trithiocarbonate species having a terminal primary hydroxyl group provided the dual initiation (Figure 13.3). The resultant polymer was terminated with a trithiocarbonate reduction of the trithiocarbonate to a thiol allows synthesis of a-hydroxyl-co-thiol polymers which are of particular interest in biopolymer applications. 

Reversible addition-fragmentation chain transfer (RAFT) polymerization has proven to be a powerful tool for the synthesis of polymers with predetermined molecular weight and low polydispersity [11, 12], In recent years, synthesis of polymers with complex molecular architecture, e.g. block and star copolymers, via the RAFT process have been reported [13],... 

Mertoglu M, Gamier S, Laschewsky A, Skrabania K, Storsberg J. Stimuli responsive amphiphilic block copolymers for aqueous media synthesised via reversible addition fragmentation chain transfer polymerisation (RAFT). Polymer 2005 46(18) 7726-40. 

---