Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Refilling included

Leaving 6 ft above and below the bed, the total tower length including space to remove the desiccant and refill would be about 28 ft. This yields an L/D of 28/5.5 = 5.0. [Pg.238]

Temperature control Adequately sized pressure relief Elimination of contaminants, including metallic residues, from process streams and equipment Selection of materials of construction compatible with the chemicaKs) in use, properly cleaned and passivated Elimination of ingress of reactive chemicals, e.g. water, air Date labelling and inventory control in storage Cleaning and inspection of reusable containers, tankers etc. before refilling ... [Pg.24]

Figure 15.4 shows a procedure for the refilling of returnable containers with a chemical of assured quality. (This will require some combination of documentation, sampling and analysis to ensure that the chemical is of the correct type, and in the intended condition.) This is applicable to drums and plastic containers, and bottles, but some modifications are necessary for pressure systems, i.e. gas cylinders, covered by the Pressure Systems Safety Regulations 2000 including ... [Pg.487]

CH, a 42-year-old man, comes into the emergency department after his sister discovered him seizing at home. He has a history of hypertension, diabetes, epilepsy, and rheumatoid arthritis. His medications include hydrochlorothiazide, gly-buride, phenytoin, and aspirin. He smokes one pack per day, drinks heavily on the weekends, and has a history of cocaine use. Upon further discussion with his sister, you discover that he stopped taking his phenytoin 4 days ago due to failure to obtain a refill from his doctor. He is currently unarousable since his last seizure 10 minutes ago. [Pg.462]

In these cultured VSMCs, about 56% of the SR released Ca2+ only in response to CPA (and, presumably, InsP3), and about 22% only in response to Caf only about 15% of the SR responded to both CPA and Caf. Moreover, the same stores could be refilled and re-emptied during a 30-60 min period (the longest times tested). These results indicate that the SR Ca2+ stores are organized into (at least) two classes of small compartments that are relatively stable. It is noteworthy that similar results have been reported in other cell types, including neurons and astrocytes (Golovina... [Pg.127]

The yellow self-adhesive Accutane qualification sticker documents that the female patient is qualified and includes the date of qualification, patient gender, cut-off date for filling the prescription, and up to a 30-day supply limit with no refills. [Pg.2031]

Prescriptions Prescriptions for controlled substances must be written in ink and include the following Date name and address of the patient name, address, and DEA number of the physician. Oral prescriptions must be promptly committed to writing. Controlled substance prescriptions may not be dispensed or refilled more than 6 months after the date issued or be refilled more than 5 times. A written prescription signed by the physician is required for schedule II drugs. In case of emergency, oral prescriptions for schedule II substances may be filled however, the physician must provide a signed prescription within 72 hours. Schedule II prescriptions cannot be refilled. A triplicate order form is necessary for the transfer of controlled substances in schedule II. Forms are available for the individual prescriber at no charge from the DEA. [Pg.2114]

Specifications included two 56-gallon FIDPE tanks, a 120 V pump, on/off float switch, rotameter with flow-rate adjustment, two pre-filters, and four filters with refillable Octolig cartridges. Size is 52"x52" with a 68 gallon spill containment. From [28] and reproduced with permission. [Pg.130]

Stepto (1997) focused on the injection molding of potato starch including the basis of the process. In addition, the rheological behavior of starch/water melts during the refill part of the injection molding cycle was analyzed quantitatively to give apparent melt viscosities. Finally, the mechanical properties of molded starch materials and the dmg-delivery behavior of starch capsules were also discussed. [Pg.454]


See other pages where Refilling included is mentioned: [Pg.46]    [Pg.15]    [Pg.231]    [Pg.369]    [Pg.1340]    [Pg.479]    [Pg.264]    [Pg.334]    [Pg.168]    [Pg.523]    [Pg.127]    [Pg.520]    [Pg.270]    [Pg.83]    [Pg.740]    [Pg.286]    [Pg.285]    [Pg.120]    [Pg.272]    [Pg.330]    [Pg.36]    [Pg.176]    [Pg.172]    [Pg.1941]    [Pg.605]    [Pg.98]    [Pg.1374]    [Pg.1375]    [Pg.234]    [Pg.130]    [Pg.232]    [Pg.112]    [Pg.236]    [Pg.11]    [Pg.1415]    [Pg.510]    [Pg.108]    [Pg.65]    [Pg.83]    [Pg.414]    [Pg.415]    [Pg.120]   
See also in sourсe #XX -- [ Pg.49 ]




SEARCH



© 2024 chempedia.info