Properties schematic representation

The results of the micromechanics studies of composite materials with unidirectional fibers will be presented as plots of an individual mechanical property versus the fiber-volume fraction. A schematic representation of several possible functional relationships between a property and the fiber-volume fraction is shown in Figure 3-4. In addition, both upper and lower bounds on those functional relationships will be obtained. 

We start by considering a schematic representation of a porous metal film deposited on a solid electrolyte, e.g., on Y203-stabilized-Zr02 (Fig. 5.17). The catalyst surface is divided in two distinct parts One part, with a surface area AE is in contact with the electrolyte. The other with a surface area Aq is not in contact with the electrolyte. It constitutes the gas-exposed, i.e., catalytically active film surface area. Catalytic reactions take place on this surface only. In the subsequent discussion we will use the subscripts E (for electrolyte) and G (for gas), respectively, to denote these two distinct parts of the catalyst film surface. Regions E and G are separated by the three-phase-boundaries (tpb) where electrocatalytic reactions take place. Since, as previously discussed, electrocatalytic reactions can also take place to, usually,a minor extent on region E, one may consider the tpb to be part of region E as well. It will become apparent below that the essence of NEMCA is the following One uses electrochemistry (i.e. a slow electrocatalytic reaction) to alter the electronic properties of the metal-solid electrolyte interface E. 

Figure 5.17. Schematic representation of a metal crystallite deposited on YSZ and of the changes induced in its electronic properties upon polarizing the catalyst-solid electrolyte interface and changing the Fermi level (or electrochemical potential of electrons) from an initial value p to a new value p -eri30 31 Reprinted with permission from Elsevier Science.

Fig. 1 Heterocycles bearing a 2-pyridone moiety with wide range of medicinal applications. Amrinone WIN 40680 1 is a cardiotonic agent for the treatment of heart failure. ZAR-NESTRA 2 is a selective farnesyl protein inhibitor and NP048 3 is a pilicide with novel antibacterial properties. The 2-pyridones 4, 5 and 6 are schematic representations of the three categories of 2-pyridones that wiU be covered in this chapter i.e., substituted 2-pyridones 4, 2-quinolones 5 and other ring-fused 2-pyridones 6...

FIG. 1 Schematic representation of the operation of the scanning polarization force microscope (SPFM). An electrically biased AFM tip is attracted toward the surface of any dielectric material. The polarization force depends on the local dielectric properties of the substrate. SPFM images are typically acquired with the tip scanning at a height of 100-300 A. (From Ref. 32.)... 

Fig. 29. Schematic representation of the longitudinal cross-section of the inclusion channel for the simple alcohol inclusions of 1 with MeOH, EtOH, and 2-PrOH 2). Hatched triangles and dotted squares represent polar areas (cf. Fig. 19, type Ila), while the rest is of apolar property...

Fig. 3 Structure-photophysical property relationship of coumarin derivatives, (a) Schematic representation of the correlation between electronic effect of substituents at the C-3 and C-7 position and photophysical properties (b) Structure and their emission maxima of various coumarins...

Figure 3. Schematic representation of a model zeolite cylindrical micropore (as for instance the AlP04-5 zeolite one). The curved inner zeolite surface is expected to influence greatly the confined molecule properties. Indeed, such a highly curved surface can be seen as composed of four surface types top, bottom, left and right surfaces.

Figure 7.17 (a) Magnetic properties of [LaTb] and [Tb2] in the form of yT versus T plot per mole of Tb(lll). (b) Schematic representation of the qubit definition, weak coupling and asymmetry, as derived from magnetic and heat capacity data. 

Fig. 1 Schematic representation of the Langmuir film balance used for the measurement of pressure-area monolayer film properties. Reprinted with permission from Arnett et al., 1989. Copyright 1989 American Chemical Society.

A schematic representation of this reactor model is shown in Figure 22.2. Particles of solid reactant B are in BMF, and fluid reactant A is uniform in composition, regardless of its flow pattern. The solid product, consisting of reacted and/or partially reacted particles of B, leaves in only one exit stream as indicated. That is, we assume that no solid particles leave in the exit fluid stream (no elutriation or entrainment of solid). This assumption, together with the assumption, as in the SCM, that particle size does not change with reaction, has an important implication for any particle-size distribution, represented by P(R). The implication is that P(R) must be the same for both the solid feed and the solid exit stream, since there is no accumulation in the vessel in continuous operation. Furthermore, in BMF, the exit-stream properties are the same as those in the vessel Thus, P(R) is the same throughout the system ... 

Figure 14 Schematic representation of the microphase separation of block copolymers. The left graph shows atomic-scale details of the phase separation at intermediate temperatures, and the right graph shows a lamellar phase formed by block copolymers at low temperatures. The block copolymers have solid-like properties normal to the lamellae, because of a well-defined periodicity. In the other two directions, the system is isotropic and has fluid-like characteristics. From reference 54.

Fig. 2 Schematic representation of (a) a luminescent dendritic sensor with signal amplification and (b) a conventional luminescent sensor. The curved arrows represent interaction processes which changes the luminescence properties (from empty to filled circles). Analyte is represented by a solid hexagon, while the recognition site is by an empty hexagon...

Figure 3.3. Schematic representation of the diagrams for the alkali metals with a selected number of elements of the p-block. In each box the solid intermediate phases are represented in the positions approximately corresponding to their compositions (long bars congruent melting phases short bars non-congruent phases). In the top part of each box every mark corresponds to a characteristic composition of the liquid phase for which the formation of an associate ( liquid compound ) may be suggested, for instance by the presence of an extremum in the trend of some property of the liquid phase. The symbol 2 L shown for certain ranges of compositions in a few diagrams indicates the presence of a miscibility gap in the liquid state, that is two liquid phases.

Fig. 2. Schematic representation of the influence of reactant structure, catalyst acid-base properties, and temperature on the selection of the elimination mechanism. For an explanation of symbols, see text. [Reprinted with permission from Berdnek and Kraus (13, p. 276). Courtesy Elsevier Scientific Publishing Company.]...

Figure 15.21 shows a schematic representation of the SCCO2 treatment effect for promoting the internal diffusion of metal ions to prepare Rh and RhPt alloy nanoparticles in mesoporous FS-16 and HMM-1. The supercritical phase displays both liquid and gas properties at the same time. SCFs can also dissolve various metal precursors, which promotes their mobiUty and surface-mediated reaction to form nanoparticles by the hydrogen reduction in the mesoporous cavities of... 

Fig. 11. Schematic representation of the binding properties of anti-idiotype antibodies and antimetatype antibodies. V, hapten a-Id, a-type anti-idiotype antibody /i-Id, /i-type anti-idiotype antibody Met, anti-metatype antibody anti-C-region, antibodies recognizing the constant region of a primary antibody (recognizing isotype or allotype).

Figure 2. Schematic representation of some relevant ground and excited-state properties of Ru(bpy)j. MLCT and MLCT are the spin-allowed and spin-forbidden metal-to-ligand charge transfer excited states, responsible for the high intensity absorption band with = 450 nm and the luminescence band with = 615 nm, respectively. The other quantities shown are intersystem crossing efficiency energy (E°°) and lifetime (x) of the MLCT state luminescence quantum yield ( ) quantum yield for ligand detachment (O,). The reduction potentials of couples involving the ground and the MLCT excited states are also indicated.

Schematic representations, like those shown in the Scheme 1, are very useful to indicate the chemical composition of the various species and to discuss the interaction between the various building blocks. Furthermore, as one can understand from the representations shown in Figures 9 and 10, the species with high nuclearity exhibit a ttu-ee-dimensional branching structure of the type of those shown by otherwise completely different dendrimers based on organic components. Therefore, endo- and exo-receptor properties can be expected, which are currently under investigation. Furthermore, aggregation of decanuclear complexes has also been demonstrated by dynamic light-scattering and conductivity experiments. Systematic studies on aggregation properties have, however, not been performed yet.

Fig. 11 Schematic representation of the concentration dependence of some physical properties for solutions of micelle-forming amphiphiles...

---