Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Pool flames

Orifice flames Pool flames Jet flames Fireball flames Flash fire flames... [Pg.210]

The flame behavior of a fire is important in determining tlie causes and effects of fires. There are several classificiitions of flames orifice flames, pool flames, fireballs. Jet fimnes, and flash fires. Orifice or pipe flames are characterized as eitlier prenii. ed flame or diffusion flmiies. Pool flames are flames on ground pools and flames on tanks. Fireballs radiate intense heat, wliich can cause fatal bums and can quickly ignite otlier materials. Jet flame or flares also radiate intense heat. [Pg.246]

Liquid Pool Flames. Liquid fuel or flammable spills often lead to fires involving a flame at the surface of the liquid. This type of diffusion flame moves across the surface of the liquid driven by evaporation of the fuel through heat transfer ahead of the flame. If the liquid pool or spill is formed at ambient conditions sufficient to vaporize enough fuel to form a flammable air/fuel mixture, then a flame can propagate through the mixture above the spill as a premixed flame. [Pg.272]

Other seemingly solid fuel flames such as those from the burning of plastics are actually more like liquid pool flames because the plastic melts and vola-tizes ahead of the advancing flame front. [Pg.272]

Giilder, O.L., Glavincevski, B., and Battista, V., Visibility of Methanol Pool Flames, 1993 Windsor Woikshop on Alternative Fuels. [Pg.76]

O. L. Guides, B. Glavincewski, and V. Battista, Visibility of methanol pool flames. Proceedings of 1993 Windsor Workshop, Toronto, Canada, 1993. [Pg.250]

The center of the flame is assumed to be 1-1/2 pool diameters from the center of the pool at a 45° elevation, in the direction of the point where radiant heat density is being considered. This assumption is used to allow for flame deflection by wind. Permissible radiant heat densities for personnel are described in the last section of this chapter. In some special cases, spacing may be governed by radiant heat exposure of certain vulnerable items of equipment, rather than personnel. Radiant heat density at the property line must not exceed 1.6 kW/m. ... [Pg.266]

The heat flux, E, from BLEVEs is in the range 200 to 350 kW/m is much higher than in pool fires because the flame is not smoky. Roberts (1981) and Hymes (1983) estimate the surface heat flux as the radiative fraction of the total heat of combustion according to equation 9.1-32, where E is the surface emitted flux (kW/m ), M is the mass of LPG in the BLEVE (kg) h, is the heat of combustion (kJ/kg), is the maximum fireball diameter (m) f is the radiation fraction, (typically 0.25-0.4). t is the fireball duration (s). The view factor is approximated by equation 9.1-34. where D is the fireball diameter (m), and x is the distance from the sphere center to the target (m). At this point the radiation flux may be calculated (equation 9.1-30). [Pg.344]

This volume does not address subjects such as toxic effects, explosions in buildings and vessels, runaway reactions, condensed-phase explosions, pool fires, jet flames, or structural responses of buildings. Furthermore, no attempt is made to cover the frequency or likelihood that a related accident scenario will occur. References to other works are provided for readers interested in these phenomena. [Pg.2]

Combustion behavior differed in some respects between continuous and instantaneous spills, and also between LNG and refrigerated liquid propane. For continuous spills, a short period of premixed burning occurred immediately after ignition. This was characterized by a weakly luminous flame, and was followed by combustion of the fuel-rich portions of the plume, which burned with a rather low, bright yellow flame. Hame height increased markedly as soon as the fire burned back to the liquid pool at the spill point, and assumed the tilted, cylindrical shape that is characteristic of a pool fire. [Pg.147]

The model is a straightforward extension of a pool-fire model developed by Steward (1964), and is, of course, a drastic simplification of reality. Figure 5.4 illustrates the model, consisting of a two-dimensional, turbulent-flame front propagating at a given, constant velocity S into a stagnant mixture of depth d. The flame base of width W is dependent on the combustion process in the buoyant plume above the flame base. This fire plume is fed by an unbumt mixture that flows in with velocity Mq. The model assumes that the combustion process is fully convection-controlled, and therefore, fully determined by entrainment of air into the buoyant fire plume. [Pg.151]

A pool fire s flame can be represented (under no wind conditions) by a vertically placed cylinder with a height h and a ground surface radius r. The view factor of... [Pg.338]

The flame radiation at a distance r from tlie pool center is given by... [Pg.213]

Dishnct fuel-specific reaction chemistry is also seen in premixed flat flames of the four butanols. Figure 2.9 shows PIE curves for m/z = 72 (C4H8O). The species pool is quite different, with butanal present in the 1-butanol flame, 2-methyl propanal in the i-butanol flame, and 2-butanone in both the 2-butanol and the f-butanol... [Pg.11]

If the release results in limited evaporation of the flammable liquid, a pool will form on the ground, and if ignited, will cause the material to bum above the liquid surface of the pool, resulting in a pool fire. Heat from the fire accelerates evaporation from the pool, sustaining the fire. Damage from pool fires is usually localized and results from radiant heat and direct flame contact. [Pg.13]

If the release forms a vapor cloud that premixes with air before ignition occurs, and turbulence is developed (for example, by the flame front propagating through a process structure), the flame speed can accelerate sufficiently to cause a blast. This event is referred to as a vapor cloud explosion. In addition to blast effects, radiant heat and flame contact effects may also occur. Flashback to the source may cause a pool and/or jet fire. [Pg.13]


See other pages where Pool flames is mentioned: [Pg.212]    [Pg.212]    [Pg.176]    [Pg.424]    [Pg.210]    [Pg.212]    [Pg.212]    [Pg.210]    [Pg.212]    [Pg.212]    [Pg.68]    [Pg.212]    [Pg.212]    [Pg.176]    [Pg.424]    [Pg.210]    [Pg.212]    [Pg.212]    [Pg.210]    [Pg.212]    [Pg.212]    [Pg.68]    [Pg.123]    [Pg.59]    [Pg.154]    [Pg.84]    [Pg.183]    [Pg.60]    [Pg.147]    [Pg.450]    [Pg.8]    [Pg.10]    [Pg.11]    [Pg.172]    [Pg.294]    [Pg.155]    [Pg.212]    [Pg.13]   
See also in sourсe #XX -- [ Pg.212 ]

See also in sourсe #XX -- [ Pg.212 ]

See also in sourсe #XX -- [ Pg.212 ]




SEARCH



Fire fundamentals pool flames

Pool fire flame height

Pool fire flame temperature

© 2026 chempedia.info