POLYISOCYANURATE

A variety of cellular plastics exists for use as thermal iasulation as basic materials and products, or as thermal iasulation systems ia combination with other materials (see Foamed plastics). Polystyrenes, polyisocyanurates (which include polyurethanes), and phenoHcs are most commonly available for general use, however, there is increasing use of other types including polyethylenes, polyimides, melamines, and poly(vinyl chlorides) for specific appHcations. 

Foamed plastics (qv) were developed in Europe and the United States in the mid-to-late 1930s. In the mid-1940s, extmded foamed polystyrene (XEPS) was produced commercially, foUowed by polyurethanes and expanded (molded) polystyrene (EPS) which were manufactured from beads (1,2). In response to the requirement for more fire-resistant ceUular plastics, polyisocyanurate foams and modified urethanes containing additives were developed in the late 1960s urea—formaldehyde, phenoHc, and other foams were also used in Europe at this time. 

Property ASTM method Polyisocyanurate XEPS EPs Polyimide Polyethylene PhenoHc... 

Condition Mean temperature, °C XEPS EPS Polyisocyanurate (PI) Aged Impermeable facing PhenoHc, faced... 

Solvent-soluble polymeric products of stmctures (1 3) can be obtained upon reaction of tetraaLkyl titanate, 2-methyl- -pentane-2,4-diol, and water in a 2 4 1 molar ratio (71). The tetraptimary glycol titanate complexes have been used as catalysts for the production of polyisocyanurates and polyoxa2ohdones (72). 

Polyurethanes. These polymers can be considered safe for human use. However, exposure to dust, generated in finishing operations, should be avoided. Ventilation, dust masks, and eye protection are recommended in foam fabrication operations. Polyurethane or polyisocyanurate dust may present an explosion risk under certain conditions. Airborne concentrations of 25—30 g/m are required before an explosion occurs. Inhalation of thermal decomposition products of polyurethanes should be avoided because carbon monoxide and hydrogen cyanide are among the many products present. 

Roofiag panels have been made from polyisocyanurate foams, both foam- and felt-reiaforced with glass fiber. PhenoHc resias are used especially for decorative laminates for paneling. The substrate may be fiberboard or a core of expanded polystyrene beads. In one case the beads are coated with phenoHc resia, then expanded ia a mold to form a stmctural foam panel. 

Cellular organic plastics. Elastomer, polystyrene, polyisocyanate, polyisocyanurate, and polyvinyl acetate. 

Table 27.4 Typical applications of cellular rigid polyurethanes and polyisocyanurates...

Whilst rigid closed-cell polyurethanes are excellent thermal insulators they do suffer from a limited and often unsatisfactory level of fire resistance, even in the presence of phosphorus-containing and halogen-containing fire retardants. Considerable promise is now being shown by the polyisocyanurates, which are also based on isocyanate chemistry. 

These materials not only have a good resistance to burning and flame spread but are also able to withstand service temperatures of up to 150°C. At the same time polyisocyanurate foams have the very good hydrolytic stability and low thermal conductivity associated with rigid polyurethane foams. 

The underlying reaction for polyisocyanurate formation is the trimerisation of an isocyanate under the influence of specific catalysts (Figure 27.9). 

Polymeric MDIs, which are also used in polyurethane foams, usually have a lower reactivity than the monomeric material but are also less volatile. The polyisocyanurate produced from this material will be of the type shown in Figure 27.11. 

---