Poly oligomer polymerization

Macrocyclic oligomer precursors of polycarbonates, PET, polymers of amides, etherketones, and ethersulfones are candidates for further study of macrocyclic oligomer polymerization thermodynamics [6]. Research extends to cyclic arylates (cyclic aryl-aryl esters) and cyclic alkyl aryl esters going back to isolating a cyclic trimer of poly(ethylene-terephthalate) in 1954 [13]. Much of the work on macrocyclic oligomers as precursors to high-MW macromolecules starts with spiro(bis)indane (SBI) biphenyl monomer to produce macrocyclic carbonates. 

Poly(arylester)-polysiloxane multiblock copolymers have also been synthesized by the interfacial polymerization of aminopropyl terminated polysiloxane oligomers with bisphenol-A and a mixture of isophthaloyl and terephthaloyl chlorides117, 193-1951 as illustrated in Reaction Scheme XV. In these reactions the poly(arylester) blocks are formed in situ during the copolymerization, so the control of their block sizes is not very precise. It is also important to note that since aminopropyl terminated siloxane oligomers are employed, the linkages which connect the arylester and siloxane blocks are amide linkages. 

ABA type poly(hydroxyethyl methacrylate) (HEMA) and PDMS copolymers were synthesized by the coupling reactions of preformed a,co-isocyanate terminated PDMS oligomers and amine-terminated HEMA macromonomers312). Polymerization reactions were conducted in DMF solution at 0 °C. Products were purified by precipitation in diethyl ether to remove unreacted PDMS oligomers. After dissolving in DMF/toluene mixture, copolymers were reprecipitated in methanol/water mixture to remove unreacted HEMA oligomers. Microphase separated structures were observed under transmission electron microscope, using osmium tetroxide stained thin copolymer films. 

Polyurethanes are thermoset polymers formed from di-isocyanates and poly functional compounds containing numerous hydroxy-groups. Typically the starting materials are themselves polymeric, but comprise relatively few monomer units in the molecule. Low relative molar mass species of this kind are known generally as oligomers. Typical oligomers for the preparation of polyurethanes are polyesters and poly ethers. These are usually prepared to include a small proportion of monomeric trifunctional hydroxy compounds, such as trimethylolpropane, in the backbone, so that they contain pendant hydroxyls which act as the sites of crosslinking. A number of different diisocyanates are used commercially typical examples are shown in Table 1.2. 

Oxidative polymerization of trans-bis-deprotected 79 under Hay coupling conditions [54] yielded, after end-capping with phenylacetylene, the high-melting and readily soluble oligomers 80a-e with the poly (triacetylene) backbone [87,106] (Scheme 8). Poly(triacetylene)s [PTAs,-(C=C-CR=CR-C=C) -] are the third class of linearly conjugated polymers with a non-aromatic allcarbon backbone in the progression which starts with polyacetylene [PA,... 

Poly(para-phenylenevinylene)s (PPVs) represent one of the most intensively investigated classes of rr-conjugated materials. Many synthetic procedures to generate unsubstituted and substituted PPVs have been developed. They include 1,6-polymerizations of 1,4-xylylene intermediates as well as several polycondensation methods. Parallel to the polymer syntheses, several series of PPV oligomers (OPVs) have been synthesized and characterized. Such model oligomers of different molecular size allow for a study of the dependence of electronic and optical properties on the length of the conjugated Ti-system. 

The spiro polymerization is a novel reaction type that uses the spiro dimerization of o-QMs to build up linear oligomers and polymers. The basic properties of the spiro dimer of a-tocopherol, that is, its fluxional structure and its ready reduction to the ethano-dimer, remain also active when such structural units are bound in the polymer. The products of the reaction, both in its poly(spiro dimeric) form (41) and in the form of the reduced polytocopherols (42), are interesting materials for application as high-capacity antioxidants, polyradical precursors, or organic metals, to name but a few. 

Polymeric plasticisers have been used as partial or total replacements for di(2-ethylhexyl)adipate (DEHA) in PVC cling film to reduce levels of plasticiser migration when used for food contact. Castle et al. [792] used SEC in combination with H 1-NMR and MS for the isolation and identification of seven individual oligomers in the most commonly employed polymeric plasticiser, poly(butylene adipate) (Reoplex R346). Both mass (RI) and specific ester moiety (UV) were being monitored (Figure 4.21). The oligomers were identified... 

---