Poly film copolymerization

VDP Polyimides. Polyimide films have also been prepared by a kind of VDP (16). The poly(amic acid) layer is first formed by the coevaporation and condensation of two monomers, followed by copolymerization on the substrate. The imidization is carried out in a separate baking step (see POLYIMIDES). 

Poly(vinyhdene chloride) (PVDC) film has exceUent barrier properties, among the best of the common films (see Barrier polymers). It is formulated and processed into a flexible film with cling and tacky properties that make it a useful wrap for leftovers and other household uses. As a component in coatings or laminates it provides barrier properties to other film stmctures. The vinyUdene chloride is copolymerized with vinyl chloride, alkyl acrylates, and acrylonitrile to get the optimum processibUity and end use properties (see Vinylidene chloride monomer and polymers). 

Qiu et al. [241 have reported the synthesis of macromolecules having 4-tolylureido pendant groups, such as poly(N-acryloyl-N -4-tolylurea-cvi ethyl acrylate) [po-ly(ATU-co-EA)] 18, and poly(N-methacryloyl-A/ -4-tol-ylurea-co-EA) [poly(MTU-co-EA)] 19, from the copolymerization of ATU and MTU with EA, respectively. Graft copolymerization of acrylamide onto the surface of these two copolymer films took place using the Ce(lV) ion as initiator. The graft copolymerization is proposed as Scheme (12). 

Figure 5.18 shows the relationship between the resistivity and phosphorus concentration of the initial solution for the film formed from various solutions and heated under the same polycrystallizing RTA conditions (750 °C for 5min). As the initial phosphorus concentration increases, the resistivity decreases down to 2.1mQcm. The film formed from a l-wt% postpolymerization addition solution and the film formed from a 0.01-wt% copolymerized solution exhibit almost the same resistivity, which is reasonable since the two films have almost the same amount of phosphorus atoms, as shown in Fig. 5.16. To apply these doped-silicon films to the source and drain regions of poly-Si TFTs, the initial concentration of 0.1-1 wt% will be sufficient in the case of the copolymerized solution for this heating condition.

LC materials have also been employed as films, plastics, and resins. Poly(l,4-benzoate) has been marketed under the name Ekonol. It decomposes before it melts, hence it does not form LC melts. Copolymerization with 4,4 -biphenol and terephthalic acid gives Ekkcel,... 

Fig. 6 Transmission electron micrograph (TEM) of the cross-section of a PDMAAm(poly-dimethylacrylamide)-b-PST(polystyrene) block-graft-copolymerized surface stained in iodine vapor, a Spurr s resin, b PST layer, c PDMAm layer, d dithiocarbamate (DC)-derivatized PST film...

Copolymerization. Vinyl chloride can be copolymerized with a variety of monomers. Vinyl acetate, the most important commercial comonomer, is used to reduce crystallinity, winch aids fusion and allows lower processing temperatures. Copolymers are used in flooring and coatings. This copolymer sometimes contains maleic add or vinyl alcohol (hydrolyzed from the poly(vinyl acetate ) to improve the coating s adhesion to other materials, including metals, Copolymers with vinylidene chloride are used as barrier films and coatings. Copolymers of vinyl chlonde with acrylic esters in latex from are used as film formers in paint, nonwoven fabric binders, adhesives, and coatings. Copolymers with olefins improve thermal stability and melt flow, but at some loss of heat-deflection temperature,... 

Electrochemical polymerization of phenols to non-conducting poly(phenylene ethers) has been described 112) and Oyama et al. recently claimed that phenol 191) and p,p -biphenol192) can be polymerized to uncharacterized conducting films. Kumar et al.193) claimed that it is possible to copolymerize phenol with pyrrole... 

In a patent dated 1965 Stowe35) laid the basis for the copolymerization of PEO macromonomer with comonomers such as acrylonitrile. It was searched for an increased wettability of polyacrylonitrile films or fibers by a permanent surface modification. ro-Styryl poly(oxyethylene) macromonomers readily copolymerize with acrylonitrile in water emulsions. They can also be copolymerized with styrene-sulfonates in the presence of poly(vinylpyrrolidone). The presence of small amounts of such copolymers in polyacrylonitrile fibers was shown to increase their wettability and their receptivity to dyes and to make them more resistant to electric loading (antistatic fibers). No characterization data on the copolymers formed have been reported. 

---