Plasticizer degradation

The ECPI approach has been adopted by the European Commission in their "Technical Guidance Document on the Risk Assessment of Notified New Substances" as the model for assessment of environmental exposure from additives in plastics. It is important to note, however, that due to the effect of ultraviolet degradation and microbial attack, a significant proportion of the emissions from flexible PVC consists of plasticizer degradation products. In these instances, therefore, the level of plasticizers appearing in the environment will be significantly less than indicated by the plasticizer loss data. 

Specimens of NR ABS/(Octa -I- AO) heat-treated at 350°-400°C developed brittleness of connected pores, whereas VO ABS (Octa -1- AO -I- EPDM), similarly treated, was tougher with large elongated pores about twice the size of the non-treated specimen. Such behavior suggests an intumescent effect of EPDM, i.e. the development of a thick porous surface layer, inhibiting the diffusion of flammable products of plastic degradation towards the gas phase and heat transfer into the plactic mass. 

This overview is an attempt to briefly cover the history and recent developments In environmentally degradable commodity and specialty polymers and plastics. Degradation pathways are mentioned, polymer types, including blends, are reported and the limitations of current testing protocols raised. The chapter concludes with generalizations on structural requirements for degradable polymers. 

A frequently cited merit of biodegradable plastics is their lack of persistance in an intact state "environmentally friendly" is a widely used vernacular phrase, but there has also been speculation in the popular press that degradable plastics will release potentially harmful additives into the environment when the plastics degrade or disintegrate. An ideal biodegradable plastic will leave no undegraded polymeric residues, and for these materials, the persistance of additives as well as the polymers must be considered. In this case, the issue is not whether or not the additive... 

Here is a green" idea TiOj can be blended into polyvinyl chloride (PVC) plastic so that the plastic degrades in sunlight.14 Ordinary PVC lasts many years in municipal landfills after it is discarded. TiOj-blended PVC would decompose in a short time. [Courtesy H. Hidaka and S. Horikoshi, Melsei University. Tokyo.]... 

In addition to these three accelerated procedures, plasticizer degradation can be measured in terms of physical properties of the film itself— flexibility, elongation, and tensile strength. This is discussed more fully later in the text. 

Melt in a plasticator must be freed of gaseous components that include moisture and air from the atmosphere and from plastics, plasticizers, and/or other additives as well as entrapped air and other gases released by certain plastics. Gas components such as moisture retention in and on plastics have always been a potential problem for all processors. All kinds of problems develop on products (splay, poor mechanical properties, dimensions, etc.). This situation is particularly important when processing hygroscopic plastics (Chapter 1). One major approach to this plastic degrading situation is by using plasticators that have vents in their barrels to release these contaminants. 

To determine the DRB the following equation is used where the value of the DRB ranges around one with the close to one. Outside the set limits can cause at least out of round and plastic degradation ... 

Calcium-, iron- and potassium-based carbon composites were evalnated for the HCI sorption capacity for use in the dehalogenation process with PVC mixed plastics degradation. It is... 

Table 18.7 Product yields and properties of liquid product from PVC mixed PP/PE/PS plastic degradation using Ca-C (6 consecutive runs) and thermal degradation. (Reproduced with permission from the American Chemical Society)...

Photoelectrochemistry The effect of light on the semiconductor-electrolyte interface is summarized. Fundamental aspects are described for microelectric device fabrication, improved coating pigments, plastic degradation, and photoelectrochemical synthesis. 

A large number of processes and reactors have been developed for the thermal conversion of plastic and rubber wastes stirred tanks, rotary kilns, fluidized beds, circulating bed reactors, screw extruders, etc. Many of the studies carried out in recent years have been based on sand fluidized or circulating bed reactors. Likewise, several works have recently appeared on plastic degradation in the presence of solvents. 

The processes of feedstock recycling of plastic wastes considered in this chapter are based on contact of the polymer with a catalyst which promotes its cleavage. In fact, plastic degradation proceeds in most cases by a combination of catalytic and thermal effects which cannot be isolated. As was described in Chapter 3, the use of catalysts is also usual in chemolysis processes of plastic depolymerization. However, there are two main differences between catalytic cracking and chemolysis there is no chemical agent incorporated to react directly with the polymer in catalytic cracking methods, and the products derived from the polymer decomposition are not usually the starting monomers. 

The catalysts commonly used to promote plastic degradation are a variety of acid solids such as amorphous silica-alumina, different types of zeolites, mesoporous aluminosilicates (MCM-41), sulfated zirconia, etc. Interesting results have also been obtained in polymer cracking over activated carbons... 

---