Pinning attachment

Procedure mounting pin. 5. While immersed in liquid nitrogen, the mounting pin (attached to crystal wand) is manoeuvred into a ctyovial... 

In parallel synthesis the compounds are prepared in separate reaction vessels but at the same time, that is, in parallel. The array of individual reaction vessels often takes the form of either a grid of wells in a plastic plate or a grid of plastic rods called pins attached to a plastic base plate (Figure 6.6) that fits into a corresponding set of wells. In the former case the synthesis is carried out on beads placed in the wells whilst in the latter case it takes place on so called... 

Figure 3. A pair of standard spreading resistance probe arm assemblies with probe pins attached, shown In measurement position on a bevelled test sample.

An index plate containing a number of circles of different-spaced holes is attached to the front of the head. The spring-loaded pin attached to the crank locates in the required hole circle. The head spindle has a central hole... 

The specimen grip system was 100 mesh stainless steel screen wrapped around 2.5 cm of each end before clamping between two stainless steel plates (0.6 cm thick) cross-serrated with 10 lines/cm. After assembly in an alignment jig, three pairs of 10-32 screws, torqued to 2.3 to 4.5 N-m (20 to 40 in-lbs), were used to clamp the grip onto the specimen. Holes in the steel plates allowed a load pin attachment to clevises on each pull-rod. The test frame design made it possible to immerse the entire system in a dewar of liquid helium. 

This procedure is used to separate crystallized product from solvent or to remove crap and solids from a liquid. Figure 8 shows the proper apparatus to use. The collecting flask is called a side arm flask and to that extended nipple (tee heel) is attached a vacuum source. The thing that is shoved through the rubber stopper is called a Buchner funnel and is usually made of white porcelain or, preferably, PP. The Buchner funnel, when viewed from above, can be seen to have lots of pin holes in the bottom surface of its reservoir. Over this surface is layered a single sheet of rounded filter paper or paper towel. 

After densiftcation, external electrode termination and leads are attached for MLC capacitor components, and pin module assembly and IC chip joining is carried out for MLC packages. The devices are then tested to ensure performance and overall reflabiUty. 

Fig. 4. Pipe or tubing die for in-line extmsion A, die body B, mandrel, pin, and male die part C, die, die bushing, and female part D, die-retaining ring E, die-retaining bolt F, die-centered bolt G, spider leg H, air hole I, seat for breaker plate J, ring for attachment to extmder and K, die land (15).

When the mold is opened, the part should be easily removable. Cavities are made with a slight taper to reduce frictional drag of the part on the mold. The half of the mold attached to the movable platen is equipped with ejector pins, which push the part out of the cavity while the mold is being opened. When the mold is closed, the pins are flush with the cavity surface. Release agents or lubricants facilitate ejection and shorten the mol ding cycle. Some complex parts require that the mold open in several directions in addition to the direction of the platen movement. For a threaded part, eg, a bottle cap, part of the mold must be rotated to remove the article from the mold. 

Transosteal and Staple Implants. This implant goes through the bone and is for the purpose of attaching dentures. The mandibular bone staple plate has replaced the transosteal pin. Since 1975 the five-pin staple bone plate has been used predominantiy, and in 1985 showed a success rate of 93% after five years (317). 

Fiber-Optic Pins. In one version of the fiber-optic pin (Benjamin et al., 1984), a small microballoon, 0.25 mm in diameter, filled with a noble gas such as argon or xenon is attached to the end of an optical fiber. When the pin is impacted, the shock heats the gas in the microballoon producing a flash which is channeled to a recording system via optical fibers. Some of the useful features of this pin are... 

Roller chains are constructed by connecting two side plates together with pins that have bushings and rollers attached. The side plates are classified as either the pin link or roller link. The pin links are located outside the roller links and connect the roller links together. This provides an alternate pin and roller link combination. 

The particular models used to demonstrate the theory obviously have many drawbacks as true representations of polymer crystals. These could include the lack of a fold energy, no distinction between new molecules and those already attached, neglect of chain ends, a somewhat arbitrary choice of pinning rules etc. However, they all serve their purpose in that they show that an energetic free energy barrier is not necessary to obtain the experimental curves. A truly representative growth picture can probably only be achieved via molecular dynamics. 

In the past, 4 x 4 in cotton patches (gauze or cellulose) have been used to estimate face and neck exposure. The patches are designed and manufactured as described above and are pinned or attached with Velcro to the back and front of a hat or protective headgear of the worker. When the exposure period is complete, the patches are removed, and... 

Figure 2.4 One of Leeuwenhoek s microscopes front, back and side views. The tiny spherical or hemispherical lens is held in the slightly raised structure in the upper part of the metal plate. The object to be examined was mounted at the tip of the sharp-pointed mounting pin. Focusing was accomplished by means of the three thumbscrews to which the mounting pin is attached. These are approximately actual size.

Figure 5.11 Attachment of T4 bacteriophage particle to the cell wall of G. coli and injection of DNA (a) Unattached particle, (b) Attachment to the wall by the long tail fibers, (c) Contact of cell wall by the tail pin. (d) Contraction of the tail sheath and injection of the DNA.

To use this device, the blasting cap may be inserted directly into the explosive or it may be connected to the explosive with primacord. In either case the firing device should be securely attached to a solid object. Run the trip wire from a fixed location to the cotter pin, leaving some slack in the line. A pull on the trip wire will remove the cotter pin, initiating the charge. 

So, if you can access the gates of the Fets, try putting in small resistors in series with them. If it is a switcher IC (with no access to the gates), try inserting a small resistor in series with the decoupling capacitor of the driver supply (usually a 0.1 pF capacitor attached to the Vdd pin and/or the bootstrap pin). Better still, pick an IC with less aggressive drive to start with. Because otherwise it will commit suicide sooner or later. 

---