Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Acylphosphine oxide photoinitiator

Materials. The radical-type photopolymerizable formulation consisted of a mixture of hexanediol diacrylate (HDDA from UCB) and a polyurethane-diacrylate (Actilane 20 from Arkros). A bis-acylphosphine oxide (BAPO from Ciba) was used as photoinitiator at a typical concentration of 1 wt %. The cationic type photopolymerizable resin consisted of a mixture of the divinylether of triethyleneglycol (RapiCure DVE-3 from ISP) and a divinylether derivative of bis-phenol A (DVE-BPA). The cationic photoinitiator (Cyracure UVI-6990 from Union Carbide) had a composition of 50 wt % of mixed triarylsulfonium hexafluorophosphate salts and 50 wt % of propylene carbonate. The BAPO initiator... [Pg.64]

The chromophore in this type of photoinitiator is frequently an aromatic carbonyl. The benzoyl radical is the major initiating species, while the other fragment may also contribute to the initiation, in some cases. The most efficient type I initiators are benzoin ether derivatives, benzil ketals, hydroxyl-alkylphenones, a-aminoketones, and acylphosphine oxides. Substituents on the aromatic carbonyl influence the absorption. [Pg.67]

When using a suitable type I photoinitiator, e.g., acylphosphine oxides and non-amine-containing acetophenones in this system, the polymerization process is very efficient and the resulting product is a 1 1 alternating copolymer. This system is susceptible to oxygen inhibition, but to a much lesser extent than acrylate polymerization. An important advantage of this system is its low toxicity. Typical components include a variety of vinyl ethers and unsaturated esters, such as maleate, fumarate, citra-conate, imides (maleimides), or N-vinylformamides. The system is also... [Pg.76]

On-aircraft repairs of composite using a rapid-cure resin system of composite component with UV light irradiation based on TRI patenP have been developed by the U.S. Air Force Research Laboratory. Alternating layers of the acrylate-based resin system and woven fiberglass (the widely used wet la)mp procedure) are applied to fill the hole and form a UV curable composition. The width of the patch can be up to 2 ft (0.6 m) and the depth as much as 0.2 in. (5 mm). The cure time using a 400 W UVA lamp is reported to be 20 min. Although it is essentially a depot repair, it can be done field when necessary to return an aircraft to service. Because of the necessity to cure relatively thick repair patches, Us-acylphosphine oxide was used as a photoinitiator. An example of the patented UV curable resin system used for the repairs is in Table 11.1. [Pg.241]

Free radical promoted, cationic polymerization also occurs upon irradiation of pyridinium salts in the presence of acylphosphine oxides. But phosphonyl radicals formed are not oxidized even by much stronger oxidants such as iodonium ions as was demonstrated by laser flash photolysis studies [51, 52]. The electron donor radical generating process involves either hydrogen abstraction or the addition of phosphorus centered or benzoyl radicals to vinyl ether monomers [53]. Typical reactions for the photoinitiated cationic polymerization of butyl vinyl ether by using acylphosphine oxide-pyridinium salt combination are shown in Scheme 10. [Pg.72]

Baxter J.E., Davidson R.S., Hagemann H.J. and Overeem T. (1988) Photoinitiators and photoinitiation, 8. The photoinduced a-cleavage of acylphosphine oxides. Identification of the initiating radicals using a model substrate. Makromol. Chem., 189, 2769-2780. [Pg.216]

Because of the wide application of Cu-catalysed systems, the redox processes based on acylphosphine oxide photoinitiators open new pathways for many reaetions in organic chemistry. [Pg.135]

IKE 08] Ikemura K., Ichizawa K., Yoshida M. et al, UV-VIS spectra and photoinitiation behaviors of acylphosphine oxide and bisacylphosphine oxide derivatives in unfilled, light-cured dental resins , Dental Materials Journal, vol. 27, no. 6, pp. 765-774, 2008. [Pg.135]

Commercially important PIj photoinitiators are aryl alkyl ketones and acylphosphine oxides. Benzoin ethers represent an important class of aryl alkyl ketones and, probably, the first class of photoinitiators used in UV curing, predominantly in the area of particle board finishing. [Pg.910]

Acylphosphine oxide and acylphosphonates with different structures have been used as photoinitiators for free-radical-initiated photopolymerization (see Table 6). [Pg.162]

C. Decker, K. Zahouily, D. Decker, T. Nguyen Thi Viet, Performance analysis of acylphosphine oxide photoinitiated polymerization . Polymer, 2001, 42, 7551-7560. [Pg.205]


See other pages where Acylphosphine oxide photoinitiator is mentioned: [Pg.73]    [Pg.272]    [Pg.74]    [Pg.31]    [Pg.31]    [Pg.344]    [Pg.74]    [Pg.402]    [Pg.99]    [Pg.213]    [Pg.116]    [Pg.188]    [Pg.322]    [Pg.35]    [Pg.92]    [Pg.232]    [Pg.90]    [Pg.99]    [Pg.402]   
See also in sourсe #XX -- [ Pg.213 ]




SEARCH



Acylphosphinates

Acylphosphine oxides

Acylphosphines

Photoinitiated

Photoinitiated oxidation

Photoinitiation

Photoinitiator

Photoinitiators

© 2024 chempedia.info