Periodic completion

Table I presents the results of "isothermal" simultaneous thermoanalytical (STA) runs, at 573 K and 773 K, for all three products. Similar data, at a fixed heating rate is shown in Table II. One of the crucial parameters is the temperature of maximum weight loss rate, corresponding to the time when dehydrochlorination of PVC starts becoming important. This temperature is close to 573 K in all cases. In fact, at a relatively fast heating rate, almost no decomposition occurs at temperatures under 563 K. If the materials are heated at 573 K for a prolonged period, complete dehydrochlorination takes place, but no further stages of PVC decomposition occur. None of the three materials investigated decomposes completely until a temperature of ca. 773 K is attained. Even then only a certain fraction of the entire mass of the samples is volatilised, due to the presence of inorganic fillers in their composition.

Monitoring Perform periodic complete blood counts and clinical chemistry tests. Monitor serum amylase levels in those individuals who have a history of elevated amylase, pancreatitis, ethanol abuse, who are on parenteral nutrition, or who are otherwise at high risk of pancreatitis. 

Improvement of clinical symptoms, lack of adverse effects periodic complete blood count with differential, routine blood chemistry growth determinations (body weight and height), blood pressure, pulse rate... 

Author 1 Author 2 Author 3 etc. Title of Article. Title of Periodical, Complete Date, Pagination. 

V = original value of the property at start of the service-life period, completely installed and ready for use, dollars Vs = salvage value of property at end of service life, dollars n = service life, years... 

R =uniform annual payments made in an ordinary annuity, dollars V = original value of a property at start of service-life period, completely... 

Periodic complete blood cell and platelet counts may be considered during prolonged therapy (rare leukopenia and/or anemia)... 

Although the addition of small amounts of acetaldehyde reduced the induction period markedly, the acceleration period and (p were unaffected until the pressure added exceeded that present just before the cool flame. In contrast, apparently, to the results of Cullis and Newitt [16], the addition of quite large amounts of acetaldehyde did not eliminate the induction period completely and only reduced the acceleration period by less than 25 %. 

Other outstanding periodicals, complete or nearly complete from their inception, are the Annales de chimie et de physique from 1789, the Philosophical Magazine from 1798, the Journal de pharmacie et de chimie from 1809, the Jernkon-torets annaler from 1817, the American Journal of Science from 1818, the Journal of the Franklin Institute from 1826, Liebig s Annalen der Chemie from 1832, the... 

Hefferlin 1996). It features a periodicity completely unrelated to atomic periodicity hence the name hyperperiodicity. ... 

As shown in Figure 5 most ethyne is converted. During the net oxidizing part of a cycle period complete conversion of both CO and C,H2 occurs. The noble metal surface becomes then almost totally covered with molecular NO and with 0 and N adatoms, and the O2 and the NO gas phase concentrations start to increase. When the concentration of the reducing reactants increases due to the inlet oscillation, the reaction with adsorbed oxygen begins and the O2 gas phase concentration decreases. 

B) undertakes periodic complete confirmatory testing with a frequency satisfactory to the Director, and... 

Periodic complete confirmatory testing of at least one lot per year per dosage form per vendor, selected on a rotational basis. 

HAZOP is time-consuming but can give a more comprehensive output. In any case, time period/completion time for such a periodic HAZOP study is specified. Also the next periodic study dates need to be finalized. 

Series Abbreviation Volumes Time period completely covered... 

A constant-composition alloy film may be deposited using flash evaporation techniques, where a small amount of the alloy material is periodically completely vaporized. This technique is used to vaporize alloys whose constituents have widely differing vapor pressures. Flash evaporation can be done using a very hot surface and dropping a pellet or periodically touching a wire tip to the surface so that the pellet or tip is completely vaporized. 

---