Passivity polarization curve

The above series of reactions indicates that pH should be a major variable affecting the position of the active-passive polarization curve of... 

Figure 9.1 Schematic Pourbaix diagram and active-passive polarization curve showing the passive region for anodic protection at Ex.

Corrosion protection of metals can take many fonns, one of which is passivation. As mentioned above, passivation is the fonnation of a thin protective film (most commonly oxide or hydrated oxide) on a metallic surface. Certain metals that are prone to passivation will fonn a thin oxide film that displaces the electrode potential of the metal by +0.5-2.0 V. The film severely hinders the difflision rate of metal ions from the electrode to tire solid-gas or solid-liquid interface, thus providing corrosion resistance. This decreased corrosion rate is best illustrated by anodic polarization curves, which are constructed by measuring the net current from an electrode into solution (the corrosion current) under an applied voltage. For passivable metals, the current will increase steadily with increasing voltage in the so-called active region until the passivating film fonns, at which point the current will rapidly decrease. This behaviour is characteristic of metals that are susceptible to passivation. 

Passivation is manifested in a polarization curve (figure C2.8.4) dashed line) by a dramatic decrease in current at a particular onset potential (the passivation potential, density, is lowered by several orders of magnitude. 

From polarization curves the protectiveness of a passive film in a certain environment can be estimated from the passive current density in figure C2.8.4 which reflects the layer s resistance to ion transport tlirough the film, and chemical dissolution of the film. It is clear that a variety of factors can influence ion transport tlirough the film, such as the film s chemical composition, stmcture, number of grain boundaries and the extent of flaws and pores. The protectiveness and stability of passive films has, for instance, been based on percolation arguments [67, 681, stmctural arguments [69], ion/defect mobility [56, 57] and charge distribution [70, 71]. 

FIG. 28-9 Typical electrochemical polarization curve for an active/passive alloy (with cathodic trace) showing active, passive, and transpassive regions and other important features. (NOTE Epp = primary passive potential, Ecaa- — freely corroding potential). 

It is worth emphasising too, that the position of those lines representing equilibria with the dissolved species, M, depend critically on the solubility of the ion, which is a continuous function of pH. For example, iron in moderately alkaline solution is expected to be very passive and so it is in borate solutions (in the absence of aggressive ions). However, the anodic polarization curve still shows a small active loop at low potential. 

In the polarization curve for anodic dissolution of iron in a phosphoric acid solution without CP ions, as shown in Fig. 3, we can see three different states of metal dissolution. The first is the active state at the potential region of the less noble metal where the metal dissolves actively, and the second is the passive state at the more noble region where metal dissolution barely proceeds. In the passive state, an extremely thin oxide film called a passive film is formed on the metal surface, so that metal dissolution is restricted. In the active state, on the contrary, the absence of the passive film leads to the dissolution from the bare metal surface. The difference of the dissolution current between the active and passive states is quite large for a system of an iron electrode in 1 mol m"3 sulfuric acid, the latter value is about 1/10,000 of the former value.6... 

Figure 11. Schematic diagram of anodic polarization curve of passive-metal electrode when sweeping electrode potential in the noble direction. The dotted line indicates the polarization curve in the absence of Cl-ions, whereas the solid line is the polarization curve in the presence of Cl ions.7 Ep, passivation potential Eb, breakdown potential Epit> the critical pitting potential ETP, transpassive potential. (From N. Sato, J, Electrochem. Soc. 129, 255, 1982, Fig. 1. Reproduced by permission of The Electrochemical Society, Inc.)...

When the polarization curve is recorded in the opposite (cathodic) direction, the electrode will regain its active state at a certain potential The activation potential is sometimes called the Flade potential (Flade, 1911). The potentials of activation and passivation as a rule are slightly different. 

FIGURE 22.2 Schematic polarization curves for spontaneous dissolution (a) of active metals (h) of passivated metals. (1,2) Anodic curves for active metals (3) cathodic curve for hydrogen evolution (4) cathodic curve for air-oxygen reduction (5) anodic curve of the passivated metal. 

Environmental tests have been combined with conventional electrochemical measurements by Smallen et al. [131] and by Novotny and Staud [132], The first electrochemical tests on CoCr thin-film alloys were published by Wang et al. [133]. Kobayashi et al. [134] reported electrochemical data coupled with surface analysis of anodically oxidized amorphous CoX alloys, with X = Ta, Nb, Ti or Zr. Brusic et al. [125] presented potentiodynamic polarization curves obtained on electroless CoP and sputtered Co, CoNi, CoTi, and CoCr in distilled water. The results indicate that the thin-film alloys behave similarly to the bulk materials [133], The protective film is less than 5 nm thick [127] and rich in a passivating metal oxide, such as chromium oxide [133, 134], Such an oxide forms preferentially if the Cr content in the alloy is, depending on the author, above 10% [130], 14% [131], 16% [127], or 17% [133], It is thought to stabilize the non-passivating cobalt oxides [123], Once covered by stable oxide, the alloy surface shows much higher corrosion potential and lower corrosion rate than Co, i.e. it shows more noble behavior [125]. 

Fig. 11-9. Anodic polarization curve of a metallic electrode for active dissolution, passivation, and transpassivation in aqueous acidic solution > u = anodic current of metal dissolution = passivation potential = transpassivation potential = maximum metal...

Fig. 11-13. Anodic polarization curve of a metallic nickel electrode in a sulfuric add solution transpassivation arises at a potential relatively dose to the flat band potential because of p-type nature of the passive oxide film. [From Sato, 1982.]...

As described in Sec. 11.3, the spontaneous corrosion potential of a corroding metal is represented by the intersection of the anodic polarization curve of metal dissolution with the cathodic polarization curve of oxidant reduction (Figs. 11—5 and 11-6). Then, whether a metal electrode is in the active or in the passive state is determined by the intersection of the anodic and cathodic polarization curves. 

Consider first the polarization curve (i.e., Tafel plot) for the anodic halfreaction occurring in corrosion of stainless steels (Fig. 16.8). The diagram for the active region is much the same as has been seen for other anodes (Figs. 15.4 to 15.7). As Eh is increased to a certain specific value, however, a sudden and dramatic drop in the anodic current density i occurs, corresponding to formation of an oxide film. At higher Eh, i remains constant at a very low level (the horizontal scale in Fig. 16.8 is logarithmic), and the metal has become passive, that is, effectively immune from corrosion. 

Figures 16.8 and 16.9 show only the anodic polarization curves for corrosion cells. The important question is, where do these curves intersect with the polarization curves for likely cathodic reactions, such as hydrogen evolution or oxygen absorption The intersection point defines the corrosion current density icorr and hence the corrosion rate per unit surface area. As an example, let us consider the corrosion of titanium (which passivates at negative Eh) by aqueous acid. In Fig. 16.10, the polarization curves for H2 evolution on Ti and for the Ti/Ti3+ couple intersect in the active region of the Ti anode. To make the intersection occur in the passive region (as in Fig. 16.11), we must either move the H+/H2 polarization curve bodily...

An interesting example of the kinetic effect in semiconductor photocorrosion is photopassivation and photoactivation of silicon (Izidinov et al., 1962). Silicon is an electronegative element, so it should be dissolved spontaneously and intensively in water with hydrogen evolution. But in most of aqueous solutions the surface of silicon is covered with a nonporous passivating oxide film, which protects it from corrosion. The anodic polarization curve of silicon (dashed line in Fig. 20) is of the form characteristic of electrodes liable to passivation as the potential increases, the anodic current first grows (the... 

Though processes occurring under photopassivation have not so far been understood in detail, they may be related with certainty (Izidinov, 1979) to the acceleration, under illumination, of one of the two conjugated reactions, which constitute the overall process of electrochemical corrosion. Depending on the initial state of corroding silicon, either the anodic (at the active surface) or the cathodic (at the passive surface) partial reaction is accelerated. This leads to the shift of the potential, and the system jumps over the maximum of the polarization curve from one stable state to the other. 

Fig. 27. Impedance diagrams measured at four points of the polarization curve of Fe in 1 MH2SO4, in the so-called passivation region. The numbers indicate frequency in Hz. From ref. 94.

Fig. 1. Polarization curve of metals with active, passive and (a) transpassive potential range including oxygen evolution (b) passive potential range going directly to oxygen evolution (c) continuing passivity for valve metals to very positive potentials. Pitting between critical pitting lim and inhibition potential fsj in the presence of aggressive anions and inhibitors.

Fig. 2 distinguishes the domains of immunity, corrosion and passivity. At low pH corrosion is postulated due to an increased solubility of Cu oxides, whereas at high pH protective oxides should form due to their insolubility. These predictions are confirmed by the electrochemical investigations. The potentials of oxide formation as taken from potentiodynamic polarization curves [10] fit well to the predictions of the thermodynamic data if one takes the average value of the corresponding anodic and cathodic peaks, which show a certain hysteresis or irreversibility due to kinetic effects. There are also other metals that obey the predictions of potential-pH diagrams like e.g. Ag, Al, Zn. 

---