Linear oligomers

Repetitive coupling of acetylenes with aryl halides is an effective way to directly build hyperbranched architecture in a stepwise manner. This type of polycoupling is often catalyzed by palladium complexes in the presence of amines and has been widely used for the preparation of well-defined oligomers, linear polymers, and perfectly branched dendrimers [19,20]. 

NbFS) TaFs Linear oligomer Linear oligomer... 

Short-chain linear oligomers are usually prepared by the same techniques as those used for the preparation of cyclic oligomers. Linear oligomers are often formed as precursors to the cyclized species. Most condensation reactions yield a mixture of cyclic and linear oligomers with the ratios of the two depending on the reaction conditions and especially on the reactant ratios. 

A large variety of protocols yielding catalytically active but ill-defined mixtures were developed in the early days of olefin metathesis. Most of them produced oligomers, linear polymers, and macrocycles but no well-defined products because of the lack of control over the polymerization [87]. Catalyst stability, reactivity, and kinetics were unsolved issues that led to broad molecular weight distributions and generally Hi-defined polymeric materials. The issue of end-group functionality could not be addressed at that time because of different termination... 

CYANACRYL acrylic elastomer NBR nitrile polymer EAE ethylene acrylic SI silicone LAOO LAB DAE 1 inear alpha olefin oligomer linear alkylated benzene dibasic acid ester ... 

Figure C2.1.2. Polymers witli linear and nonlinear chain architectures. The nonlinear polymers can have branched chains. Short chains of oligomers can be grafted to tire main chain. The chains may fonn a. stor-like stmcture. The chains can be cross-linked and fonn a network.

Ziegler found that adding certain metals or their compounds to the reaction mixture led to the formation of ethylene oligomers with 6-18 carbons but others promoted the for matron of very long carbon chains giving polyethylene Both were major discoveries The 6-18 carbon ethylene oligomers constitute a class of industrial organic chemicals known as linear a olefins that are produced at a rate of 3 X 10 pounds/year m the... 

The chemistry of furfuryl alcohol polymerization has received much attention over the years. Several recent reviews have been written (5,6,54). Based on the accumulated data, furfuryl alcohol has to be considered a bifimctional monomer in the initial stage and its "normal" reactions give linear chains or oligomers containing essentially two repeating units (15,16) with (16) predominating. 

Polymers from either of these homologous series can be made to predominate by usiag a small excess of the diamine or diacid, respectively. In addition to these linear polymers, cycHc oligomers are also formed, though ia this case n... 

As the length and frequency of branches increase, they may ultimately reach from chain to chain. If all the chains are coimected together, a cross-linked or network polymer is formed. Cross-links may be built in during the polymerisation reaction by incorporation of sufficient tri- or higher functional monomers, or may be created chemically or by radiation between previously formed linear or branched molecules (curing or vulcanisation). Eor example, a Hquid epoxy (Table 1) oligomer (low molecular weight polymer) with a 6-8 is cured to a cross-linked soHd by reaction of the hydroxyl and... 

The value for the heat of fusion of PPS, extrapolated to a hypothetical 100% crystalline state, is not agreed upon in the literature. Reported values range from approximately 80 J/g (19 cal/g) (36,96,101) to 146 J/g (35 cal/g) (102), with one intermediate value of 105 J/g (25 cal/g) (20). The lower value, 80 J/g, was originally measured by thermal analysis and then correlated with a measure of crystallinity deterrnined by x-ray diffraction (36). The value of 146 J/g was deterrnined independendy on uniaxiaHy oriented PPS film samples by thermal analysis, density measurement via density-gradient column, and the use of a calculated density for 100% crystalline PPS to arrive at a heat of fusion for 100% crystalline PPS (102). The value of 105 J/g was obtained by measuring the heats of fusion of weU-characterized linear oligomers of PPS and extrapolation to infinite molecular weight. 

The manufacture of polydimethylsiloxane polymers is a multistep process. The hydrolysis of the chlorosilanes obtained from the direction process yields a mixture of cycHc and linear sdanol-stopped oligomers, called hydrolysate (eq. 7) (21). In some cases, chloro-stopped polymers can also be obtained (59). 

The ratio of cycHc to linear oligomers, as well as the chain length of the linear sdoxanes, is controlled by the conditions of hydrolysis, such as the ratio of chlorosilane to water, temperature, contact time, and solvents (60,61). Commercially, hydrolysis of dim ethyl dichi oro sil a n e is performed by either batch or a continuous process (62). In the typical industrial operation, the dimethyl dichi orosilane is mixed with 22% a2eotropic aqueous hydrochloric acid in a continuous reactor. The mixture of hydrolysate and 32% concentrated acid is separated in a decanter. After separation, the anhydrous hydrogen chloride is converted to methyl chloride, which is then reused in the direct process. The hydrolysate is washed for removal of residual acid, neutralized, dried, and filtered (63). The typical yield of cycHc oligomers is between 35 and 50%. The mixture of cycHc oligomers consists mainly of tetramer and pentamer. Only a small amount of cycHc trimer is formed. 

In contrast to the hydrolysis technology, the methanolysis process allows for the one-step synthesis of organosdoxane oligomers and methyl chloride without formation of hydrochloric acid (64,65). The continuous methanolysis can also yield quantitatively linear sdanol-stopped oligomers by recycle of the cycHc fraction into the hydrolysis loop. 

When the catalyst is triethylamine, the yield is nearly 100% cycHc oligomers but if pyridine is used, the polymer is nearly 100% linear. A basic catalyst in the second step, such as lithium stearate or an organic titanate [bis-(acetylacetonato)diisopropoxytitanium], produces a polycarbonate with a molecular weight of 250,000—300,000 when polymerized at 300°C for 30 min. A fiber glass composite has been prepared using this basic procedure (39). 

---