Olefin conversion numbers

Numbers opposite olefins are percentage olefin conversions, numbers below them are percentage selectivities to stated products. Other products are mainly CO and C02. 

The conversion of fatty alcohols is approximately 99%. The reaction product is then condensed and sent to a distillation column to remove water and high boilers. Typically, a-olefin carbon-number distribution is controlled by the alcohol composition of the reactor feed. The process is currentiy used to produce a-olefins from fatty alcohols. A typical product composition is at <5%, at 50—70%, C g at 30—50%, C2Q at <2%,... 

We looked at a number of water soluble cosolvents (Table 28.3). In all cases aldehyde products were observed. 1,4-dioxane compares well with ethanol as a co-solvent. The data so far shows that 1,4-dioxane shows slightly lower olefin conversion after two hours than ethanol, but shghtly better selectivity. 

Entry Catalyst Type of TPP Conversion (%) Number of recycling cycles Paraffin (%) Iso-olefins (%) Aldehydes (%) nil (M)... 

We cite isomerization of Cs-Ce paraffinic cuts, aliphatic alkylation making isoparaffinic gasoline from C3-C5 olefins and isobutane, and etherification of C4-C5 olefins with the C1-C2 alcohols. This type of refinery can need more hydrogen than is available from naphtha reforming. Flexibility is greatly improved over the simple conventional refinery. Nonetheless some products are not eliminated, for example, the heavy fuel of marginal quality, and the conversion product qualities may not be adequate, even after severe treatment, to meet certain specifications such as the gasoline octane number, diesel cetane number, and allowable levels of certain components. 

Residual monomers in the latex are avoided either by effectively reacting the monomers to polymer or by physical or chemical removal. The use of tert-huty peroxypivalate as a second initiator toward the end of the polymeri2ation or the use of mixed initiator systems of K2S20g and tert-huty peroxyben2oate (56) effectively increases final conversion and decreases residual monomer levels. Spray devolatili2ation of hot latex under reduced pressure has been claimed to be effective (56). Residual acrylonitrile also can be reduced by postreaction with a number of agents such as monoamines (57) and dialkylamines (58), ammonium—alkali metal sulfites (59), unsaturated fatty acids or their glycerides (60,61), their aldehydes, esters of olefinic alcohols, cyanuric acid (62,63), andmyrcene (64). 

Olefin isomerization can be catalyzed by a number of catalysts such as molybdenum hexacarbonyl [13939-06-5] Mo(CO)g. This compound has also been found to catalyze the photopolymerization of vinyl monomers, the cyclization of olefins, the epoxidation of alkenes and peroxo species, the conversion of isocyanates to carbodiimides, etc. Rhodium carbonylhydrotris(triphenylphosphine) [17185-29-4] RhH(CO)(P(CgH )2)3, is a multifunctional catalyst which accelerates the isomerization and hydroformylation of alkenes. 

TS-1 is a material that perfectly fits the definition of single-site catalyst discussed in the previous Section. It is an active and selective catalyst in a number of low-temperature oxidation reactions with aqueous H2O2 as the oxidant. Such reactions include phenol hydroxylation [9,17], olefin epoxida-tion [9,10,14,17,40], alkane oxidation [11,17,20], oxidation of ammonia to hydroxylamine [14,17,18], cyclohexanone ammoximation [8,17,18,41], conversion of secondary amines to dialkylhydroxylamines [8,17], and conversion of secondary alcohols to ketones [9,17], (see Fig. 1). Few oxidation reactions with ozone and oxygen as oxidants have been investigated. 

Some other processes are based on a severe hydrotreatment followed by a stage for octane recovery. Octgain from ExxonMobil [57] and ISAL from UOP-Intevep [58], Deep desulfurization is achieved by an increase in severity, causing lost in octane by olefins saturation. In the first case, in a second reactor octane number is recovered by a combination of cracking and isomerization reactions. In the latter case, the catalyst employed during desulfurization possess isomerization capabilities inhibiting an excessive octane lost. Other mentioned functionalities of the catalyst include dealkylation and conversion. 

The increasing volume of chemical production, insufficient capacity and high price of olefins stimulate the rising trend in the innovation of current processes. High attention has been devoted to the direct ammoxidation of propane to acrylonitrile. A number of mixed oxide catalysts were investigated in propane ammoxidation [1]. However, up to now no catalytic system achieved reaction parameters suitable for commercial application. Nowadays the attention in the field of activation and conversion of paraffins is turned to catalytic systems where atomically dispersed metal ions are responsible for the activity of the catalysts. Ones of appropriate candidates are Fe-zeolites. Very recently, an activity of Fe-silicalite in the ammoxidation of propane was reported [2, 3]. This catalytic system exhibited relatively low yield (maximally 10% for propane to acrylonitrile). Despite the low performance, Fe-silicalites are one of the few zeolitic systems, which reveal some catalytic activity in propane ammoxidation, and therefore, we believe that it has a potential to be improved. Up to this day, investigation of Fe-silicalite and Fe-MFI catalysts in the propane ammoxidation were only reported in the literature. In this study, we compare the catalytic activity of Fe-silicalite and Fe-MTW zeolites in direct ammoxidation of propane to acrylonitrile. 

For the range of industrially relevant conditions, the developed model could accurately predict both the observed CO conversion and the products distribution up to n = 49, in terms of total hydrocarbons, n-paraffins, and a-olefins. In particular, using thirteen adaptive parameters, the model is able to describe the typical deviations of the product distribution from the ASF model, i.e., the methane high selectivity, the low selectivity to C2 species, and the change of the slope of the ASF plot with growing carbon number. Accordingly, the present model can be applied to identify optimized process conditions that are suitable to grant the desired conversion with the requested products distribution. 

---