Normal molybdenum

In general molybdenum disulphide is chemically very inert. It is resistant to attack by most acids, except aqua regia and hot concentrated sulphuric, nitric and possibly hydrochloric acids. Whereas most metals form salts when attacked by acids, molybdenum has no such tendency, and the product of acid attack is normally molybdenum trioxide. The same appears to be true of the disulphide, and the limited attack by acids can be considered more as a form of oxidation. There is considerable variation in the resistance of different samples to acid attack, and the reactions involved may therefore be primarily those of contaminants rather than of the molybdenum disulphide itself. 

The normal daily requirement of molybdenum, at 25 pg (Anke et al. 1989, Turnlund et al. 1995), is very low compared with the daily intake. The normal molybdenum requirement is 0.4 pg kg body weight. The diet consumed should contain 90 pg Mokg DM (Holzinger et al. 1998a, b, 1997, Anke et al. 1993a, Anke and Glei 1993, Reiss and Anke 2002). 

Only limited - and somewhat unreliable -data are available on the effects of human exposure to molybdenum. The population of Ankavan (Armenia Republic) takes in between two- and 10-fold more molybdenum via local foodstuffs (10-15 mg Mo per day) than people in areas with a normal molybdenum supply (Kovalskij... 

The distribution of molybdenum in the body is also determined by the Mo offer. In the case of a normal molybdenum supply meeting the requirements, liver, kidney, and lung store most molybdenum per kg dry matter. Skeleton musculature and hair accumulate little molybdenum [14]. 

The structurally similar molybdenum disulfide also has a low coefficient of friction, but now not increased in vacuum [2,30]. The interlayer forces are, however, much weaker than for graphite, and the mechanism of friction may be different. With molecularly smooth mica surfaces, the coefficient of friction is very dependent on load and may rise to extremely high values at small loads [4] at normal loads and in the presence of air, n drops to a near normal level. 

Carbon content is usually about 0.15% but may be higher in bolting steels and hot-work die steels. Molybdenum content is usually between 0.5 and 1.5% it increases creep—mpture strength and prevents temper embrittlement at the higher chromium contents. In the modified steels, siUcon is added to improve oxidation resistance, titanium and vanadium to stabilize the carbides to higher temperatures, and nickel to reduce notch sensitivity. Most of the chromium—molybdenum steels are used in the aimealed or in the normalized and tempered condition some of the modified grades have better properties in the quench and tempered condition. 

In addition to oxidation itself, gas diffusion into the base metal can be more damaging than the actual loss of metal from the surface. Thus the loss in mechanical properties owing to diffusion of oxygen into niobium makes it more difficult to protect niobium against oxidation damage than molybdenum, even though molybdenum has less resistance to normal oxidation effects than niobium. 

Incandescent Lamps, Electronic Tubes, and Resistance Elements. Articles fashioned in any form from molybdenum and tungsten usually fall within the bounds of powder metallurgy. These metals normally are first produced as a powder. Both molybdenum and tungsten are used as targets in x-ray tubes, for stmctural shapes such as lead and grid wires in electron tubes, and as resistance elements in furnaces. 

Figures Background-subtracted, normalized, and ili -weighted Mo K-edge EXAFS, versus k (A ), for molybdenum metal foil obtained from the primary experimental data of Figure 2 with Eq = 20,025 eV.

Work by the US Bureau of Mines" involving galvanic couple experiments showed that the normally low corrosion rates of molybdenum were reduced further by contact with aluminium, SAE 1 430 steel or magnesium in aerated solutions of synthetic sea water or 3% sodium chloride. 

Molybdenum tends to be protected by vanadium in aerated 7 1 % hydrochloric acid and it receives a high degree of protection when coupled with copper in this medium. Molybdenum corrodes somewhat faster than normal in 3 1 % nitric acid when coupled with tungsten. It is not affected by contact with titanium in 3-1% nitric acid. It is protected by aluminium and copper in aerated 10% formic acid and by aluminium in air-aerated 9% oxalic acid. In the latter solution, copper had only a slight protective effect when coupled with molybdenum. 

Because these variables have a very pronounced effect on the current density required to produce and also maintain passivity, it is necessary to know the exact operating conditions of the electrolyte before designing a system of anodic protection. In the paper and pulp industry a current of 4(KX) A was required for 3 min to passivate the steel surfaces after passivation with thiosulphates etc. in the black liquor the current was reduced to 2 7(X) A for 12 min and then only 600 A was necessary for the remainder of the process . From an economic aspect, it is normal, in the first instance, to consider anodically protecting a cheap metal or alloy, such as mild steel. If this is not satisfactory, the alloying of mild steel with a small percentage of a more passive metal, such as chromium, molybdenum or nickel, may decrease both the critical and passivation current densities to a sufficiently low value. It is fortunate that the effect of these alloying additions can be determined by laboratory experiments before application on an industrial scale is undertaken. 

---