Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Mist lubrication

Oil viscosity grades have also been developed with suitable additives for use in a variety of specific appHcations in two-cycle engines, refrigeration and air conditioning, oil mist lubricators, low outdoor temperatures, instmments, and office machines as partially reflected in Table 3. Equipment manufacturers and lubricant suppHers provide recommendations for individual cases. [Pg.239]

Although not widely used for gears, oil-mist lubrication is nevertheless worth mentioning here. It is a total loss technique in which the oil is supplied in the form of fine droplets carried by compressed air. Two virtues are that the lubricant can be carried long distances through pipes without severe frictional losses, and that no oil pumps are needed since the motive power is provided by factory compressed-air lines. However, unless such systems are totally enclosed, the exhaust can create a build-up of oil-mist in the atmosphere. In order to maintain good standards of industrial hygiene, it is recommended that... [Pg.859]

When pure oil mist lubrication is specified, oil rings or flingers (if any) and constant level oilers shall not be provided, and a mark indicating the oil level is not required. When purge mist lubrication is specified, these items shall be provided and the oiler shall be piped so that it is maintained at the internal pressure of the bearing honsing. [Pg.38]

Note At pumping temperatures above 300°C (570°F), bearing housings with pure oil mist lubrication may require special features to reduce heating of the bearing races by heat transfer from the pumpage. Typical features are as follows ... [Pg.38]

When specified, provisions shall be made for either pure oil or purge oil mist lubrication (see 2.9.2.7 for requirements). [Pg.38]

Are provisions to be made for pure or purge oil mist lubrication Yes No... [Pg.169]

A245 Oil mist lubrication OIL MIST L c 1 Ainone Brpurge oil mist C pure oil mist Z other... [Pg.186]

Macks, E.F., Nemeth, Z.N. and Anderson, W.J., Preliminary Investigation of Molybdenum Disulfide - Air Mist Lubrication for Roller Beanhgs Operating to DN Values of 1 x 10 and Ball Bearings Operating to Temperatures of 1,000°F, NACA/T1B/3109 RME 51G31, (October, 1951). [Pg.342]

Spray and mist lubrication Low risk of contamination. High cost of hardware and installation. [Pg.1514]

Wilson, T.C. (1970) Qd Mist Lubrication Process and Novel Lubricating Qd Composition for Use Therein . US Patent 3,510,425. [Pg.188]

LUBRICATION, MIST - Lubrication by an oil mist produced by injecting oil into a gas stream. [Pg.99]

I m older now, and much wiser. As discussed in the following section, use of an oil mist lubrication system eliminates all of the problems with erroneous oiler glass level indications and with moisture in the lube oil. [Pg.500]

However, I now understand that the oil mist lubrication system is superior to the wet sump system. In the oil mist method of bearing lubrication, a small stream of air containing atomized lube oil is... [Pg.500]

See other pages where Mist lubrication is mentioned: [Pg.221]    [Pg.918]    [Pg.842]    [Pg.859]    [Pg.865]    [Pg.1020]    [Pg.17]    [Pg.17]    [Pg.17]    [Pg.38]    [Pg.38]    [Pg.29]    [Pg.17]    [Pg.17]    [Pg.17]    [Pg.63]    [Pg.63]    [Pg.97]    [Pg.183]    [Pg.185]    [Pg.191]    [Pg.192]    [Pg.192]    [Pg.221]    [Pg.741]    [Pg.1062]    [Pg.181]    [Pg.1065]    [Pg.922]    [Pg.99]    [Pg.110]    [Pg.258]   
See also in sourсe #XX -- [ Pg.185 ]



SEARCH



Mist

© 2024 chempedia.info