Microporous/mesoporous solids

Micropore-Mesoporous solids (Activated carbon type)... 

Stein, A. (2003) Advances in microporous and mesoporous solids -Highlights of recent progress. Advanced Materials, 15, 763-775. 

Pores are found in many solids and the term porosity is often used quite arbitrarily to describe many different properties of such materials. Occasionally, it is used to indicate the mere presence of pores in a material, sometimes as a measure for the size of the pores, and often as a measure for the amount of pores present in a material. The latter is closest to its physical definition. The porosity of a material is defined as the ratio between the pore volume of a particle and its total volume (pore volume + volume of solid) [1]. A certain porosity is a common feature of most heterogeneous catalysts. The pores are either formed by voids between small aggregated particles (textural porosity) or they are intrinsic structural features of the materials (structural porosity). According to the IUPAC notation, porous materials are classified with respect to their sizes into three groups microporous, mesoporous, and macroporous materials [2], Microporous materials have pores with diameters < 2 nm, mesoporous materials have pore diameters between 2 and 50 nm, and macroporous materials have pore diameters > 50 nm. Nowadays, some authors use the term nanoporosity which, however, has no clear definition but is typically used in combination with nanotechnology and nanochemistry for materials with pore sizes in the nanometer range, i.e., 0.1 to 100 nm. Nanoporous could thus mean everything from microporous to macroporous. 

Peng, L. and Grey, C.P. (2008) Diphosphine probe molecules and solid-state NMR investigations of proximity between addle sites in zeolite HY. Micropor. Mesopor. Mater., 116, 277-283. 

Sarsani, V.R. and Subramaniam, B. (2009) Isobutane/butene alkylation on microporous and mesoporous solid acid catalysts probing the pore transport effeds with liquid and near critical reaction media. Green Chem., 11, 102-108. 

Recently, the Horvath-Kawazoe (HK) method for slit-like pores [40] and its later modifications for cylindrical pores, such as the Saito-Foley (SF) method [41] have been applied in calculations of the mesopore size distributions. These methods are based on the condensation approximation (CA), that is on the assumption that as pressure is increased, the pores of a given size are completely empty until the condensation pressure corresponding to their size is reached and they become completely filled with the adsorbate. This is a poor approximation even in the micropore range [42], and is even worse for mesoporous solids, since it attributes adsorption on the pore surface to the presence of non-existent pores smaller than those actually present (see Fig. 2a) [43]. It is easy to verify that the area under the HK PSD peak corresponding to actually existing pores does not provide their correct volume, so the HK-based PSD is not only excessively broad, but also provides underestimated volume of the actual pores. This is a fundamental problem with the HK-based methods. An additional problem is that the HK method for slit-like pores provides better estimates of the pore size of MCM-41 with cylindrical pores than the SF method for cylindrical pores. This shows the lack of consistency [32,43]. Since the HK-based methods use CA, one can replace the HK or SF relations between the pore size and pore filling pressure by the properly calibrated ones, which would lead to dramatic improvement of accuracy of the pore size determination [43] (see Fig. 2a). However, this will not eliminate the problem of artificial tailing of PSDs, since the latter results from the very nature of HK-based methods. 

Potential of post-synthesis functionalized microporous and mesoporous solids... 

Catalysts for Fine Chemical Synthesis, Vol. 4, Microporous and Mesoporous Solid Catalysts Edited by E. Derouane 2006 John Wiley Sons, Ltd... 

POTENTIAL OF POST-SYNTHESIS FUNCTIONALIZED MICROPOROUS AND MESOPOROUS SOLIDS AS CATALYSTS FOR FINE CHEMICAL SYNTHESIS... 

Applications of Zeolites and other Microporous and Mesoporous Solids to Catalytic Fine Chemical Synthesis... 

---