Aluminum metallurgy

Use Fluoridation, laundry sours, opalescent glass, vitreous enamel frits, metallurgy (aluminum and beryllium), insecticides and rodenticides, chemical intermediate, glue, leather and wood preservative, moth repellent, manufacture of pure silicon. 

Hydrogen cyanide Iron oxide black Mercury chloride (ic) Nickel cyanide Nitric acid Sodium chloride Sulfurous acid Zirconium potassium hexafluoride metallurgy, aluminum Sodium silicofluoride metallurgy, beryllium Sodium silicofluoride metallurgy, ore separation Phosgene metals... 

Domack, M. S., Stress Corrosion Evaluation of Powder Metallurgy Aluminum Alloy 7091 with the Breaking Load Test Method, Presented at the Tri-Service Corrosion Conference, Colorado Springs, CO, 5-7 May 1987, p. 21... 

Hexafluorozirconic acid is used ia metal finishing and cleaning of metal surfaces, whereas the fluorozirconates are used in the manufacture of abrasive grinding wheels, in aluminum metallurgy, ceramics industry, glass manufacturing, in electrolytic cells, in the preparation of fluxes, and as a fire retardant (see Abrasives Metal surface treati nts). 

Metallurgy. Lithium forms alloys with numerous metals. Early uses of lithium alloys were made in Germany with the production of the lead alloy, BahnmetaH (0.04% Li), which was used for bearings for railroad cars, and the aluminum alloy, Scleron. In the United States, the aluminum alloy X-2020 (4.5% Cu, 1.1% Li, 0.5% Mn, 0.2% Cd, balance Al) was introduced in 1957 for stmctural components of naval aircraft. The lower density and stmctural strength enhancement of aluminum lithium alloys compared to normal aluminum alloys make it attractive for uses in airframes. A distinct lithium—aluminum phase (Al Li) forms in the alloy which bonds tightly to the host aluminum matrix to yield about a 10% increase in the modules of elasticity of the aluminum lithium alloys produced by the main aluminum producers. The density of the alloys is about 10% less than that of other stmctural aluminum alloys. 

Sihcon carbide is comparatively stable. The only violent reaction occurs when SiC is heated with a mixture of potassium dichromate and lead chromate. Chemical reactions do, however, take place between sihcon carbide and a variety of compounds at relatively high temperatures. Sodium sihcate attacks SiC above 1300°C, and SiC reacts with calcium and magnesium oxides above 1000°C and with copper oxide at 800°C to form the metal sihcide. Sihcon carbide decomposes in fused alkahes such as potassium chromate or sodium chromate and in fused borax or cryohte, and reacts with carbon dioxide, hydrogen, ak, and steam. Sihcon carbide, resistant to chlorine below 700°C, reacts to form carbon and sihcon tetrachloride at high temperature. SiC dissociates in molten kon and the sihcon reacts with oxides present in the melt, a reaction of use in the metallurgy of kon and steel (qv). The dense, self-bonded type of SiC has good resistance to aluminum up to about 800°C, to bismuth and zinc at 600°C, and to tin up to 400°C a new sihcon nitride-bonded type exhibits improved resistance to cryohte. 

Figure 8.1 Effect of pH on corrosion of 1100-H14 alloy (aluminum) by various chemical solutions. Observe the minimal corrosion in the pH range of 4-9. The low corrosion rates in acetic acid, nitric acid, and ammonium hydroxide demonstrate that the nature of the individual ions in solution is more important than the degree of acidity or alkalinity. (Courtesy of Alcoa Laboratories from Aluminum Properties and Physical Metallurgy, ed. John E. Hatch, American Society for Metals, Metals Park, Ohio, 1984, Figure 19, page 295.)...

Because alterations to equipment design can be cumbersome and expensive, a more economical approach may be to change the metallurgy of affected components. Metals used in typical cooling water environments vary in their resistance to erosion-corrosion. Listed in approximate order of increasing resistance to erosion-corrosion, these are copper, brass, aluminum brass, cupronickel, steel, low-chromium steel, stainless steel, and titanium. 

Nonferrous metallurgy is as varied as the ores and finished products. Almost every thermal, chemical, and physical process known to engineers is in use. The general classification scheme that follows gives an understanding of the emissions and control systems aluminum (primary and secondary), beryllium, copper (primary and secondary), lead (primary and secondary), mercury, zinc, alloys of nonferrous metals (primary and secondary), and other nonferrous metals. 

Metallurgy is another cost versus operability factor for heat exchangers. For example, for seawater service some companies specify 90/10 Cu-Ni tubes as minimum and do not allow the cheaper, but more prone to corrosion, aluminum-brass. One can even consider going on up to 70/30 Cu-Ni, or to one of the modern, high-performance... 

But first the synthesis had to come John was interested in reduced metal halides, particularly for the post-transition metals cadmium, galHum, and bismuth (his Ph.D. dissertation was on anhydrous aluminum halides and mixed halide intermediates, a good start for what was to come ). However, he was not yet actively interested in rare-earth metals and their remarkable solubility in their halides. But these elements lured him one floor below where Adrian Daane headed the metallurgy section of Spedding s empire. He knew how to produce rare-earth metals with high purity and in sufficient quantity and also how to handle tantalum containers. What if one gave it a tr/ and reduced some rare-earth metal halides (John insists that this term is used correctly) from their respective metals at high temperatures under appropriate conditions. 

G. Pastztov, The Possibility of Producing Aluminum with Higher Purity on the Basis of the Electrochemical Model of Electrolysis, Mineral Processing and Extractive Metallurgy Review, Vol. 8, p. 119, 1992. 

Used industrially as a chlorinating agent, dehydrating agent, catalyst, in the manufacture of pharmaceuticals, and in aluminum metallurgy. 

---