Mechanical amorphization

Summing np, we discussed four main rontes toward nanoprocessing of hydrides in ball mills. These are as follows  

All of these syntheses are preceded by mechanical activation of reagents in ball mills and aU of them can be considered when mannfacturing of nanohydride powders is anticipated. However, solid-state reaction rontes are not always well investigated, and can be complex. More often than not, the yields of reactions leading to nanohydrides are not reaching 100% and an amorphons phase, which provides lower storage capacity, is formed. 

---

Liao I,.Senna M. Thermal behavior of mechanically amorphized talc. Thermochimica Acta 1992 197 295-306. 

No polymer is ever 100% crystalline at best, patches of crystallinity are present in an otherwise amorphous matrix. In some ways, the presence of these domains of crystallinity is equivalent to cross-links, since different chains loop in and out of the same crystal. Although there are similarities in the mechanical behavior of chemically cross-linked and partially crystalline polymers, a significant difference is that the former are irreversibly bonded while the latter are reversible through changes of temperature. Materials in which chemical cross-linking is responsible for the mechanical properties are called thermosetting those in which this kind of physical cross-linking operates, thermoplastic. 

Between T j, and Tg, depending on the regularity of the polymer and on the experimental conditions, this domain may be anything from almost 100% crystalline to 100% amorphous. The amorphous fraction, whatever its abundance, behaves like a supercooled liquid in this region. The presence of a certain degree of crystallinity mimics the effect of crosslinking with respect to the mechanical behavior of a sample. 

To a large extent, the properties of acryUc ester polymers depend on the nature of the alcohol radical and the molecular weight of the polymer. As is typical of polymeric systems, the mechanical properties of acryUc polymers improve as molecular weight is increased however, beyond a critical molecular weight, which often is about 100,000 to 200,000 for amorphous polymers, the improvement is slight and levels off asymptotically. 

Noncrystalline domains in fibers are not stmctureless, but the stmctural organization of the polymer chains or chain segments is difficult to evaluate, just as it is difficult to evaluate the stmcture of Hquids. No direct methods are available, but various combinations of physicochemical methods such as x-ray diffraction, birefringence, density, mechanical response, and thermal behavior, have been used to deduce physical quantities that can be used to describe the stmcture of the noncrystalline domains. Among these quantities are the amorphous orientation function and the amorphous density, which can be related to some of the important physical properties of fibers. 

Density, mechanical, and thermal properties are significantly affected by the degree of crystallinity. These properties can be used to experimentally estimate the percent crystallinity, although no measure is completely adequate (48). The crystalline density of PET can be calculated theoretically from the crystalline stmcture to be 1.455 g/cm. The density of amorphous PET is estimated to be 1.33 g/cm as determined experimentally using rapidly quenched polymer. Assuming the fiber is composed of only perfect crystals or amorphous material, the percent crystallinity can be estimated and correlated to other properties. 

Dynamic mechanical measurements were made on PTEE samples saturated with various halocarbons (88). The peaks in loss modulus associated with the amorphous relaxation near —90°C and the crystalline relaxation near room temperature were not affected by these additives. An additional loss peak appeared near —30° C, and the modulus was reduced at all higher temperatures. The amorphous relaxation that appears as a peak in the loss compliance at 134°C is shifted to 45—70°C in the swollen samples. 

Transitions. Samples containing 50 mol % tetrafluoroethylene with ca 92% alternation were quenched in ice water or cooled slowly from the melt to minimise or maximize crystallinity, respectively (19). Internal motions were studied by dynamic mechanical and dielectric measurements, and by nuclear magnetic resonance. The dynamic mechanical behavior showed that the CC relaxation occurs at 110°C in the quenched sample in the slowly cooled sample it is shifted to 135°C. The P relaxation appears near —25°C. The y relaxation at — 120°C in the quenched sample is reduced in peak height in the slowly cooled sample and shifted to a slightly higher temperature. The CC and y relaxations reflect motions in the amorphous regions, whereas the P relaxation occurs in the crystalline regions. The y relaxation at — 120°C in dynamic mechanical measurements at 1 H2 appears at —35°C in dielectric measurements at 10 H2. The temperature of the CC relaxation varies from 145°C at 100 H2 to 170°C at 10 H2. In the mechanical measurement, it is 110°C. There is no evidence for relaxation in the dielectric data. 

Some amorphous copoly(ether—sulfone) fkms have been prepared (117) with Ts around 130°C with no loss in weight up to 400°C in ak or N2. Other backbones iavestigated in this class of polymers are copoly(ether—amides) (118) and copoly(ether—ketones) (119). These polymers show good mechanical properties, flow characteristics, and abrasion resistance. 

The following mechanisms in corrosion behavior have been affected by implantation and have been reviewed (119) (/) expansion of the passive range of potential, (2) enhancement of resistance to localized breakdown of passive film, (J) formation of amorphous surface alloy to eliminate grain boundaries and stabilize an amorphous passive film, (4) shift open circuit (corrosion) potential into passive range of potential, (5) reduce/eliminate attack at second-phase particles, and (6) inhibit cathodic kinetics. 

---