Reduction loose

With the distinction between economical and loose reduction in mind, let s turn to Kim s treatment of multiply realizable properties in chapter 4 of MIPW. We may suppose, with Kim, that the exclusion argument provides a strong reason to seek a reduction of mental properties to physical properties we may also note — though Kim does not — that the reduction will afford a solution only if it is an economical one. The ostensible problem with multiply realizable mental properties is that their multiplicity of realizers apparently precludes strong type reductions pain cannot be identified with the firing of C fibers if some creatures realize... 

The discrepancy between the pore area or the core area on the one hand and the BET area on the other is proportionately larger with silica than with alumina, particularly at the higher degrees of compaction. The fact that silica is a softer material than alumina, and the marked reduction In the BET area of the compact as compared with that of the loose material, indicates a considerable distortion of the particles, with consequent departure of the pore shape from the ideal of interstices between spheres. The factor R for cylinders (p. 171), used in the conversion to pore area in the absence of a better alternative, is therefore at best a crude approximation. 

The manufacture of metal in powder form is a complex and highly engineered operation. It is dominated by the variables of the powder, namely those that are closely connected with an individual powder particle, those that refer to the mass of particles which form the powder, and those that refer to the voids in the particles themselves. In a mass of loosely piled powder, >60% of the volume consists of voids. The primary methods for the manufacture of metal powders are atomization, the reduction of metal oxides, and electrolytic deposition (15,16). Typical metal powder particle shapes are shown in Figure 5. 

Cavitation Loosely regarded as related to water hammer and hydrauhc transients because it may cause similar vibration and equipment damage, cavitation is the phenomenon of collapse of vapor bubbles in flowing liquid. These bubbles may be formed anywhere the local liquid pressure drops below the vapor pressure, or they may be injected into the hquid, as when steam is sparged into water. Local low-pressure zones may be produced by local velocity increases (in accordance with the Bernouhi equation see the preceding Conservation Equations subsection) as in eddies or vortices, or near bound-aiy contours by rapid vibration of a boundaiy by separation of liquid during water hammer or by an overaU reduction in static pressure, as due to pressure drop in the suction line of a pump. 

Apart from the application of XPS in catalysis, the study of corrosion mechanisms and corrosion products is a major area of application. Special attention must be devoted to artifacts arising from X-ray irradiation. For example, reduction of metal oxides (e. g. CuO -> CU2O) can occur, loosely bound water or hydrates can be desorbed in the spectrometer vacuum, and hydroxides can decompose. Thorough investigations are supported by other surface-analytical and/or microscopic techniques, e.g. AFM, which is becoming increasingly important. 

The anodic oxidation of the iron is usually localized in surface pits and crevices which allow the formation of adherent rust over the remaining surface area. Eventually the lateral extension of the anodic area undermines the rust to produce loose flakes. Moreover, once an adherent film of rust has formed, simply painting over gives but poor protection. This is due to the presence of electrolytes such as iron(II) sulfate in the film so that painting merely seals in the ingredients for anodic oxidation. It then only requites the exposure of some other portion of the surface, where cathodic reduction can take place, for rusting beneath the paint to occur. 

Temperature programmed reduction (TPR) experiments. TPRs were performed for each material using a quartz reactor tube (4 mm i d ), in which a 100 mg sample was mounted on loosely packed quartz wool. Samples were predried overnight at 120 °C. The sample was heated at 5 °C /min up to 700 °C under 20 mL/min flow of a 2 1 mixture of H2 Ar. 

Reaction 6 representing /1-scission of alkoxyl radicals leading to the reduction of molar mass competes with transfer of a free radical centre to surrounding groups with consequent formation of alcoholic groups (reaction 7), which subsequently loose water and C = C unsaturation appears randomly along the polymer chain. 

It was not until 1987, before a second model on electrocodeposition was published by Buelens [37, 58], From experimental observations on the codeposition of particles on a rotating disk electrode (RDE) as a function of current density, rotation speed and bath composition, that could not be explained by Guglielmi, she suggested that a particle will only be incorporated into the deposit if a certain amount of the adsorbed ions on the particle surface is reduced. This is one possible way to account for the field-assisted adsorption, held responsible for the transition between loosely and strongly adsorbed particles in the model of Guglielmi. This proposition yields the probability P(k/K,i) for the incorporation of a particle based on the reduction of k out of K ions, bound to its surface, at current density i... 

Reduction in prestress due to stress relaxation under continuously applied load can lead to looseness of joints or leakage of seals. 

---