Kick-backs

Positive pumps are normally fitted with relief valves. These are not usually fitted to centrifugal pumps unless the process material is likely to explode if it gets too hot. As an alternative to a relief valve, such pumps may be fitted with a high-temperature trip. This isolates the power supply. Or a kick-back, a small-diameter line (or a line with a restrietion orifice plate) leading from the delivery line baek to the suction vessel, may be used. The line or orifice plate is sized so that it will pass just enough liquid to prevent the pump from overheating. Small-diameter tines are better than restriction orifice plates as they are less easily removed. 

If a pump is required to deliver a very small fraction of its design rate, a kick-back should be provided. 

In the plant pathology literature, only systemic fungicides with kick-back action are considered curative, but here, we include any pesticides that limit further spread of pests and diseases in the plant population. Provided no petroleum-based synergists or carriers are used. 

Valve fails shut. As for I Valve overheats. Covered by a). b) Install kick-back on pumps... 

NONE No Flow 1. Flow stopped upstream. 2. Line blockage OT the isolation valve shut in error. 3. Line fracture. No absorption in column. Entire process stops as tail-gas Row As for I. Pressure buildup in pipe and secon cooler. As for I. Gases escape into the surroundings. a) Ensure liquid feeds to absorber and Stops.Other process units shut down. b) Install LOW FLOW ALARM onto the FIC. Covered by a) and b). dary c) Install kick-back on upstream pumps and ensure pressure relief system is adequate. Covered by a) and b). d) Ensure regular patrolling of feed transfer lines. e) Plant emergency shutdown procedures. 

NONE No Flow 1. Pump failure. 2. Valve fails shut. 3. Line fracture. High emissions of NOx in tail gas. As for. Valve overheats. AS for I and 2. a) Install HIGH LEVEL ALARM on TIC on the tail-gas outlet line to indicate high emissions. Covered by a). b) Install kick-back on pumps. Covered by a) and b). C) Regular inspection and patrolling of cooling-water circuit lines and associated seals. 

A paradise for divers and snorkelers and a place to kick back for everybody else, the Keys are a popular destination for just about anybody seeking some sun. The first place to fill your cooler on the Overseas Highway is at Good Food Conspiracy (US 1, Mile Marker 30.2, Big Pine Key, b 305-872-3945), a funky little natural food store. 

Feel a touch of the Florida Keys while kicking back at Old Dog New Trick Cafe (307 Exchange Alley, b 504-522-4569). You ll miss Florida s cooling breezes as you sit outdoors in the hot and sultry French Quarter, but you ll enjoy the quick and light all-vegetarian fare. Items such as polenta stuffed with black beans and feta and grilled tofu with peanut ginger sauce make this a unique New Orleans find. 

BONAIRE Kick back for eight Lazy Days and Dreamy Nights at Harbour Village Beach Club (800-424-0004 harbour... 

C. A skirt of the same material that kicks back 45 degrees and extends 18 inches. 

When the task or a series of tasks is finished, reward yourself Kick back, grab a cup of coffee, enjoy one of those candy bars hidden in your desk, or take a walk around the offiee or the block. Stressed spelled backwards is desserts Offset some of that intense work with one or more pleasurable desserts. ... 

Helping to secure project financing Fraud Engineer/architect steers client, owner, or customer to a specific lender in return for a kick-back from the lender ... 

To begin, cut a board the length of a radius of the circle you wish to cut, plus extra for a handle. Mark a line across the board for the saw slot (1) and bore it out (2) (be careful of saw kick-back as you do this). Clamp the edger to the sawbar, insert the bar through the slot and bolt the unit to the board (3). Measure from the inside edge of a chain cutter and mark the desired radius in the center of the board (4). Drive a spike through the board at that mark for a pivot (5), and tack the spike into the center of the circle. Start the saw and enter the cut by pushing the handle end of the board (6). 

Leak from Compressor 2 kick-back loop... 

Following HAZOP of this modified design it was found that additional failure cases were present at the new compressors. Due to the need for immediate switchover to the parallel compressors, the equipment items would be at process conditions and therefore pose identical hazards as the operational compressors. In the QRA duplicate failure cases are used to represent loss of containment from the kick-back loops around each compressor. As this is a simplified case study no other changes were made to the QRA. 

Another unacceptable excuse used to justify late reporting of acci-dents/incidents is the lack of understanding by the safety department. For instance, if the safety department does not accept or gives back acci-dent/incident reports that are incomplete and deemed unacceptable, supervisors have been known to use this as an excuse for late reporting. From the supervisor s point of view, there is little reason to turn in a report that is incomplete when that supervisor realizes that the report will be kicked back by the safety department when the shortcoming is realized. In this case, the supervisor might wonder why the report should not just... 

Are saws used for ripping equipped with anti-kick back devices and spreaders ... 

---