Colloids INDEX

Many attempts have been made to characterize the stabiUty of the colloidal state of asphalt at ordinary temperature on the basis of chemical analysis in generic groups. For example, a colloidal instabiUty index has been defined as the ratio of the sum of the amounts in asphaltenes and flocculants (saturated oils) to the sum of the amounts in peptizers (resins) and solvents (aromatic oils) (66) ... 

We introduce, for the sake of convenience, species indices 5 and c for the components of the fluid mixture mimicking solvent species and colloids, and species index m for the matrix component. The matrix and both fluid species are at densities p cr, Pccl, and p cr, respectively. The diameter of matrix and fluid species is denoted by cr, cr, and cr, respectively. We choose the diameter of solvent particles as a length unit, = 1. The diameter of matrix species is chosen similar to a simplified model of silica xerogel [39], cr = 7.055. On the other hand, as in previous theoretical works on bulk colloidal dispersions, see e.g.. Ref. 48 and references therein, we choose the diameter of large fluid particles mimicking colloids, cr = 5. As usual for these dispersions, the concentration of large particles, c, must be taken much smaller than that of the solvent. For all the cases in question we assume = 1.25 x 10 . The model for interparticle interactions is... 

Widespread medicinal use of colloidal bismuth subcitrate (CBS) has prompted extensive studies of bismuth compounds involving the citrate anion. Bismuth citrate is essentially insoluble in water, but a dramatic increase in solubility with increasing pH has been exploited as a bio-ready source of soluble bismuth, a material referred to as CBS. Formulation of these solutions is complicated by the variability of the bismuth anion stoichiometry, the presence of potassium and/ or ammonium cations, the susceptibility of bismuth to oxygenation to Bi=0, and the incorporation of water in isolated solids. Consequently, a variety of formulas are classified in the literature as CBS. Solids isolated from various, often ill-defined combinations of bismuth citrate, citric acid, potassium hydroxide, or ammonium hydroxide have been assigned formulas on the basis of elemental analysis data or by determination of water and ammonia content, but are of low significance in the absence of complementary data other than thermal analysis (163), infrared spectroscopy (163), or NMR spectroscopy (164). In this context, the Merck index lists the chemical formula of CBS as KgfNHJaBieOafOHMCeHsCbh in the 11th edition (165), but in the most recent edition provides a less precise name, tripotassium dicitrato bismuthate (166). 

For the evaluation of the response of the sensor, we selected several vapors of different polarity. The vapors included water (H20), acetonitrile (ACN), toluene, and dichloromethane (DCM). Solvent polarity and refractive index of tested vapors are listed in Table 4.346 47. The spectral range for the evaluation of the vapor responses of the colloidal crystal film was selected as 700 995 nm, which covered only the fundamental Bragg diffraction peak on the (111) planes of the colloidal crystal film to further reduce effects from possible stacking defects in the film as suggested in the literature44. 

Phase functions can also be used to measure the size and refractive index of a microsphere, and they have been used by colloid scientists for many years to determine particle size. Ray et al. (1991a) showed that careful measurements of the phase function for an electrodynamically levitated microdroplet yield a fine structure that is nearly as sensitive to the optical parameters as are resonances. This is demonstrated in Fig. 21, which presents experimental and theoretical phase functions obtained by Ray and his coworkers for a droplet of dioctylphthalate. The experimental phase function is compared with two... 

In one example, the colloidal structure, is made by sedimentation of polystyrene beads, giving voids in the range 120-1000 mn, and the voids are filled with TiO generated from titanium tetrapropoxide. The polystyrene bead lattice is then removed by calcining to give an iridescent material, but not with a full photonic band gap. In this case one of the controlling factors is the refractive index of the matrix, which needs to be greater than 2.8. 

Underwood S, Mulvaney P (1994) Effect of the Solution Refractive-Index on the Color of Gold Colloids. Langmuir 10 3427-3430... 

---