Impeller heat transfer

Figure 14-2 presents visuals of commonly used mechanical agitator impellers. Heat transfer correlations for these impellers are presented later. The reader is referred to Chapter 6 for information on their performance characteristics and guidelines for their selection and use. 

Commonly used heat-transfer surfaces are internal coils and external jackets. Coils are particularly suitable for low viscosity Hquids in combination with turbine impellers, but are unsuitable with process Hquids that foul. Jackets are more effective when using close-clearance impellers for high viscosity fluids. For jacketed vessels, wall baffles should be used with turbines if the fluid viscosity is less than 5 Pa-s (50 P). For vessels equipped with cods, wall baffles should be used if the clear space between turns is at least twice the outside diameter of the cod tubing and the fluid viscosity is less than 1 Pa-s (10... 

When concentric banks of hehcal cods are used, the process side heat-transfer coefficient b for the cod bank closest to the impeller is as given by the foregoing equation. For the second and third banks, the heat-transfer coefficient is 70 and 40% of the calculated value, respectively. 

If severe heat-transfer requirements are imposed, heating or cooling zones can be incorporated within or external to the CSTR. For example, impellers or centrally mounted draft tubes circulate Hquid upward, then downward through vertical heat-exchanger tubes. In a similar fashion, reactor contents can be recycled through external heat exchangers. 

David and Colvin [Am. Inst. Chem. Eng. J., 7, 72 (1961)]. Continuous heat transfer between kerosine and water unbaffled vessel. Open impellers (paddles and propellers) are better than closed (centrifugal and disk impellers) at the same tip speed. 

Close-Clearance Stirrers For some pseiidoplastic fluid systems stagnant fluid may be found next to the -essel walls in parts remote from propeller or turbine impellers. In such cases, an anchor impeller maybe used (Fig, 18-6), The fluid flow is principally circular or helical (see Fig, 18-7) in the direction of rotation of the anchor. Whether substantial axial or radial fluid motion also occurs depends on the fluid iscosity and the design of the upper blade-supporting spokes. Anchor agitators are used particularly to obtain irnpro ed heat transfer in high-consistency fluids,... 

Likewise, large-diameter impellers (D > Df/2) are useful for (1) avoiding stagnant regions in slurries, (2) short mixing times to obtain uniformity throughout a vessel, (3) promotion of heat transfer, and (4) laminar continuous averaging of slurries. 

Heat Transfer In general, the fluid mechanics of the film on the mixer side of the heat transfer surface is a function of what happens at that surface rather than the fluid mechanics going on around the impeller zone. The impeller largely provides flow across and adjacent to the heat-transfer surface and that is the major consideration of the heat-transfer result obtained. Many of the correlations are in terms of traditional dimensionless groups in heat transfer, while the impeller performance is often expressed as the impeller Reynolds number. 

The fluidfoil impellers (shown in Fig. 18-2) usually give more flow for a given power level than the traditional axial- or radial-flow turbines. This is also thought to be an advantage since the heat-transfer surface itself generates the turbulence to provide the film coefficient and more flow should be helpful. This is true to a limited degree in jacketed tanks (Fig. 18-34), but in helical coils (Fig. 18-35), the... 

A basic stirred tank design is shown in Fig. 23-30. Height to diameter ratio is H/D = 2 to 3. Heat transfer may be provided through a jacket or internal coils. Baffles prevent movement of the mass as a whole. A draft tube enhances vertical circulation. The vapor space is about 20 percent of the total volume. A hollow shaft and impeller increase gas circulation (as in Fig. 23-31). A splasher can be attached to the shaft at the hquid surface to improve entrainment of gas. A variety of impellers is in use. The pitched propeller moves the liquid axially, the flat blade moves it radially, and inclined blades move it both axially and radially. The anchor and some other designs are suited to viscous hquids. 

Equipment suitable for reactions between hquids is represented in Fig. 23-37. Almost invariably, one of the phases is aqueous with reactants distributed between phases for instance, NaOH in water at the start and an ester in the organic phase. Such reac tions can be carried out in any kind of equipment that is suitable for physical extraction, including mixer-settlers and towers of various kinds-, empty or packed, still or agitated, either phase dispersed, provided that adequate heat transfer can be incorporated. Mechanically agitated tanks are favored because the interfacial area can be made large, as much as 100 times that of spray towers, for instance. Power requirements for L/L mixing are normally about 5 hp/1,000 gal and tip speeds of turbine-type impellers are 4.6 to 6.1 i7i/s (15 to 20 ft/s). 

This chapter reviews the various types of impellers, die flow patterns generated by diese agitators, correlation of die dimensionless parameters (i.e., Reynolds number, Froude number, and Power number), scale-up of mixers, heat transfer coefficients of jacketed agitated vessels, and die time required for heating or cooling diese vessels. 

Table 7-4 shows flow patterns and applications of some commercially available impellers. Generally, the axial flow pattern is most suitable for flow sensitive operation such as blending, heat transfer, and solids suspension, while the radial flow pattern is ideal for dispersion operations that require higher shear levels than are provided by axial flow impellers. Myers et al. [5] have described a selection of impellers with applications. Further details on selection are provided by Uhl and Gray [6], Gates et al. [7], Hicks et al. [8] and Dickey [9]. 

The power per unit volume thus inereases slightly. Eor equal heat transfer eoeffieients on small and large seales, the larger tank will use an impeller at a lower speed. 

Impeller speed of rotation, rpm Power number, dimensionless Prandl number (heat transfer)... 

Basically, anything that can be done to reduce the temperature of the product by removal of heat generated by the cyclical stress will improve the possibilities of surviving the cyclical stress. If the heat transfer capability is limited, then the only alternative is to use stiff materials and low stress levels on the product compared with the strength capability of the material. The heavier products that result will be relatively inefficient in the use of material. In some cases when the load applied is an inertial load (such as an impeller on a pump) it may be that only a trade-off of weight for low stress level can cause failure. 

---