Hydroxyls water and

With fresh activated-clay catalyst, endothermic peaks are observed at temperatures of about 300, 1200, and 1600°F. These three peaks are attributed to loss of physically adsorbed water, loss of chemically bound (hydroxyl) water, and collapse of the montmorillonite structure, respectively. The hydroxyl water originally present amounts to 3 or 4%. The magnitude of the peak at 1200°F. decreases if the sample is heated above 800°F. prior to thermal analysis, and disappears completely if the sample is calcined at 1100°F. The thermal-analysis curve for the dehydrated catalyst is flat up to the point at which the montmorillonite structure begins to disappear. If the catalyst has not been heated above 1450°F., it becomes rehydrated upon exposure to moisture and a new endothermic peak appears in the curve between 800 and 1000°F. The size of the new peak increases as that of the original hydroxyl-water peak decreases it corresponds to 1.5 to 2.0% sorbed water with catalyst that has been rehydrated after calcination at 1100°F. The rehydration capacity of the catalyst decreases as the catalyst becomes partially deactivated with use. 

The vibrations of protons in minerals hydroxyl, water and ammonium. 1065 ... 

In ambient air copper initially forms a film with a total thickness of around 3 nm. It seems to contain at least two layers, both of which contain copper as Cu. The inner layer close to the metal consists of CujO and the outer layer of bound hydroxyl, water, and adventitious hydrocarbon [67]. Cu dissolves into the aqueous layer as Cu, which readily oxidizes to Cu +. From the presence of both Cu (soft acid) and Cu + (intermediate acid) a variety of corrosion products are expected. 

J D and R H Fowler 1933. A Theory of Water and Ionic Solution, with Particular Reference to rdrogen and Hydroxyl Ions. Journal of Chemical Physics 1 515-548. 

The excess of unchanged acetic anhydride is then hydrolysed by the addition of water, and the total free acetic acid estimated by titration with standard NaOH solution. Simultaneously a control experiment is performed identical with the above except that the alcohol is omitted. The difference in the volumes of NaOH solution required in the two experiments is equivalent to the difference in the amount of acetic add formed, i.e., to the acetic acid used in the actual acetylation. If the molecular weight of the alcohol is known, the number of hydroxyl groups can then be calculated. 

Organohthium and organomagnesium compounds are stable species when prepared m suitable solvents such as diethyl ether They are strongly basic however and react instantly with proton donors even as weakly acidic as water and alcohols A proton is transferred from the hydroxyl group to the negatively polarized carbon of the organometallic compound to form a hydrocarbon... 

The relationship between the BET monolayer capacity of physically adsorbed water and the hydroxyl content of the surface of silica has been examined by Naono and his co-workers in a systematic study, following the earlier work by Morimoto. Samples of the starting material—a silica gel—were heated for 4 hours in vacuum at a succession of temperatures ranging from 25 to 1000°C, and the surface concentration of hydroxyl groups of each sample was obtained from the further loss on ignition at 1100°C combined with the BET-nitrogen area. Two complete water isotherms were determined at 20°C on each sample, and to ensure complete... 

In Table 5.3, is compared with the total hydroxyl concentration (Ni, + N ) of the corresponding fully hydroxylated, sample. The results clearly demonstrate that the physical adsorption is determined by the total hydroxyl content of the surface, showing the adsorption to be localized. It is useful to note that the BET monolayer capacity n JH2O) (= N ) of the water calculated from the water isotherm by the BET procedure corresponds to approximately 1 molecule of water per hydroxyl group, and so provides a convenient means of estimating the hydroxyl concentration on the surface. Since the adsorption is localized, n.(H20) does not, of course, denote a close-packed layer of water molecules. Indeed, the area occupied per molecule of water is determined by the structure of the silica, and is uJH2O) 20A ... 

Thus in Fig. 5.22 the first outgassing at 25°C will have removed physisorbed water only, so that curve (1) is the isotherm of physical adsorption on the fully hydroxylated material. The 300°C outgassing, on the other hand, will have removed all the ligand water and the majority of the hydroxyl groups when isotherm (4) is determined, therefore, the Ti ions will chemisorb ligand water at low relative pressure, but the number of hydroxyl groups reformed will be very small. 

Antimony Oxide as a Primary Flame Retardant. Antimony oxide behaves as a condensed-phase flame retardant in cellulosic materials (2). It can be appHed by impregnating a fabric with a soluble antimony salt followed by a second treatment that precipitates antimony oxide in the fibers. When the treated fabric is exposed to a flame, the oxide reacts with the hydroxyl groups of the cellulose (qv) causing them to decompose endothermically. The decomposition products, water and char, cool the flame reactions while slowing the production and volatilization of flammable decomposition products (see Flaa retardants for textiles). 

Study of the mechanism of this complex reduction-Hquefaction suggests that part of the mechanism involves formate production from carbonate, dehydration of the vicinal hydroxyl groups in the ceUulosic feed to carbonyl compounds via enols, reduction of the carbonyl group to an alcohol by formate and water, and regeneration of formate (46). In view of the complex nature of the reactants and products, it is likely that a complete understanding of all of the chemical reactions that occur will not be developed. However, the Hquefaction mechanism probably involves catalytic hydrogenation because carbon monoxide would be expected to form at least some hydrogen by the water-gas shift reaction. 

The mixture is kept for 3 hours at 105°C after the oxide addition is complete. By this time, the pressure should become constant. The mixture is then cooled to 50°C and discharged into a nitrogen-filled botde. The catalyst is removed by absorbent (magnesium siUcate) treatment followed by filtration or solvent extraction with hexane. In the laboratory, solvent extraction is convenient and effective, since polyethers with a molecular weight above about 700 are insoluble in water. Equal volumes of polyether, water, and hexane are combined and shaken in a separatory funnel. The top layer (polyether and hexane) is stripped free of hexane and residual water. The hydroxyl number, water, unsaturation value, and residual catalyst are determined by standard titration methods. 

Physical properties of isopropyl alcohol are characteristic of polar compounds because of the presence of the polar hydroxyl, —OH, group. Isopropyl alcohol is completely miscible ia water and readily soluble ia a number of common organic solvents such as acids, esters, and ketones. It has solubiUty properties similar to those of ethyl alcohol (qv). There is a competition between these two products for many solvent appHcations. Isopropyl alcohol has a slight, pleasant odor resembling a mixture of ethyl alcohol and acetone, but unlike ethyl alcohol, isopropyl alcohol has a bitter, unpotable taste. 

---