Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Heat-treated treatment

It has been established that special heat-treated treatment to surface of nanodispersed diamond effective for hydrogen electrode material creation. [Pg.547]

Keywords Hydrogen oxidation, oxygen reduction, nanodispersed diamond, surface, heat-treated treatment, hydrogen electrode, oxygen electrode. [Pg.547]

The development of diamond catalysts involved special two-stage treatment of the diamond nanopowder surface, the so-called modifications. Figure 1 gives the schematic of the reception of electrode materials. As is seen from the schematic, the hydrogen electrode was make from special heat-treated treatment in the hydrogen environment [6]. [Pg.548]

It follows that the special heat-treated treatment in hydrogen environment has allowed us increased exchange current density by a factor of 1,8-2,0. At concentration change from 0,1 to 1,0 N exchange current density grows. At concentration change from 1,0 to 4,0 N exchange current density remains practically constant. Therefore, concentration of culfuric acid equal 1,0 is optimum. [Pg.549]

Figure 3 compares the exchange current densities on the initial nanodispersed diamond (4), modified nanodispersed diamond (after heat - treated treatment)(5), acetylene black AD-100 (1) and on the known catalysts tungsten (2) and vanadium (3) carbides. The specific surfaces of all samples of the powders were about 140 rrr/g. The exchange current density on modified diamond nanopowders is higher than that on tungsten or vanadium carbides by a factor of 1.6. [Pg.549]

This two-stage heat-treated treatment has allowed us to produce an active layer on the diamond surface that catalyzes the hydrogen oxidation, to give efectifive catalists for hydrogen electrodes. [Pg.549]

The special heat-treated treatment in hydrogen environment has allowed us efectifive catalists for hydrogen electrodes. [Pg.552]

Heat-transfer media Heat-transfer medium Heat-transfer oils Heat-transfer view Heat treating polyester Heat treatment Heavy crude oil Heavy-duty engines Heavy fuel oil Heavy gas oil Heavy metal Heavy metals... [Pg.466]

Fluoridation of potable water suppHes for the prevention of dental caries is one of the principal uses for sodium fluoride (see Water, municipal WATER treatment). Use rate for this appHcation is on the order of 0.7 to 1.0 mg/L of water as fluoride or 1.5 to 2.2 mg/L as NaF (2). NaF is also appHed topically to teeth as a 2% solution (see Dentifrices). Other uses are as a flux for deoxidiziag (degassiag) rimmed steel (qv), and ia the resmelting of aluminum. NaF is also used ia the manufacture of vitreous enamels, ia pickling stainless steel, ia wood preservation compounds, caseia glues, ia the manufacture of coated papers, ia heat-treating salts, and as a component of laundry sours. [Pg.237]

The estabhshment of safe thermal processes for preserving food in hermetically sealed containers depends on the slowest heating volume of the container. Heat-treated foods are called commercially sterile. Small numbers of viable, very heat-resistant thermophylic spores may be present even after heat treatment. Thermophylic spores do not germinate at normal storage temperatures. [Pg.458]

Some treatments are practiced so widely that untreated material is essentially unknown ia the jewelry trade. The heating of pale Fe-containing chalcedony to produce red-brown carnelian is one of these. Another example iavolves turquoise where the treated material is far superior ia color stabiUty. Such treatments have traditionally not been disclosed. Almost all blue sapphire on the market has been heat treated, but it is not possible to distinguish whether it was near-colorless comndum containing Fe and Ti before treatment, or whether it had already been blue and was only treated ia an attempt at marginal improvement. The irradiation of colorless topa2 to produce a blue color more iatense than any occurring naturally is, however, self-evident, and treatments used on diamond are always disclosed. [Pg.220]

Cladding and backing metals are purchased in the appropriately heat-treated condition because corrosion resistance is retained through bonding. It is customary to supply the composites in the as-bonded condition because hardening usually does not affect the engineering properties. Occasionally, a post-bonding heat treatment is used to achieve properties required for specific combinations. [Pg.150]

P/M steels can be heat treated in the same manner as cast or wrought steels. They may be austenitized, quenched, and tempered. Surface hardening includes pack or gas carburization or nitriding, ie, heating in a nitrogen-containing atmosphere. Because of the greater amount of exposed surface area in the form of porosity, a protective atmosphere is needed (see Metal surface treatments). [Pg.187]

Steam treatment imparts increased corrosion resistance for ferrous P/M parts. The parts are heated to 400—600°C and then exposed to superheated steam. After cooling, the parts are usually oil dipped to further increase corrosion and wear resistance, and to enhance appearance (see Corrosion and CORROSION control). Heat treated parts are seldom steam treated because annealing reduces hardness and tensile strength. [Pg.187]

Heat Treatment of Steel. Steels are alloys having up to about 2% carbon in iron plus other alloying elements. The vast application of steels is mainly owing to their ability to be heat treated to produce a wide spectmm of properties. This occurs because of a crystallographic or aHotropic transformation which takes place upon quenching. This transformation and its role in heat treatment can be explained by the crystal stmcture of iron and by the appropriate phase diagram for steels (see Steel). [Pg.236]

Quenching. After solution treatment, the product is generally cooled to room temperature at such a rate to retain essentially all of the solute in solution. The central portions of thicker products caimot be cooled at a sufficient rate to prevent extensive precipitation in some alloys. Moreover, some forgings and castings are dehberately cooled slowly to minimize distortion and residual stress produced by differential cooling in different portions of the products. Cold water, either by immersion or by sprays, is the most commonly used cooling medium. Hot water or a solution of a polymer in cold water is used when the highest rates are not desired. Dilute Al—Mg—Si and Al—Mg—Zn extmsions can be effectively solution heat treated by the extmsion process therefore, they may be quenched at the extmsion press by either air or water. [Pg.123]

Following wet processing, fine particle size kaolins may be calcined, ie, heat treated at about 1000°C. This treatment converts the kaolin to an amorphous pigment of significantly higher brightness and opacity (8). Properties of the various types of kaolins used in paper are shown in Table 2. [Pg.206]

Use for heat treating is also small compared to the past. It has been supplanted to a large extent by furnaces using special atmospheric conditions. Heat treatment salts containing sodium cyanide are used for small metal parts when selective case hardening is required. [Pg.384]

Miscellaneous uses for sodium cyanide include heat treating, metal stripping, and compounds used for clearing smut. Treatment of wood chips with sodium cyanide and CaCl2 reportedly increases the kraft cooking yield of pulp (qv) (64). [Pg.384]


See other pages where Heat-treated treatment is mentioned: [Pg.547]    [Pg.547]    [Pg.547]    [Pg.547]    [Pg.87]    [Pg.5]    [Pg.389]    [Pg.502]    [Pg.68]    [Pg.150]    [Pg.328]    [Pg.330]    [Pg.375]    [Pg.130]    [Pg.179]    [Pg.211]    [Pg.467]    [Pg.123]    [Pg.385]    [Pg.393]    [Pg.452]   
See also in sourсe #XX -- [ Pg.521 ]

See also in sourсe #XX -- [ Pg.521 ]




SEARCH



Heat treating

Heat treatment

© 2024 chempedia.info